Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

McWire Z-Axis Stepper Directions

by Demented Chihuahua
1,416 3 02/07/2008 04:25PM
Last Post by ZachHoeken

DC motor driver stepper hack problems compiling

by andy hall
1,383 3 02/06/2008 03:08PM
Last Post by andy hall

Nanotech steppers, anyone run them in bi-polar parallel..? results???

by John R
1,658 3 02/06/2008 10:38AM
Last Post by nophead

Power Comms 1.3 Voltage Tolerances?

by Ithacacian
1,639 13 02/06/2008 09:49AM
Last Post by ZachHoeken

PWM Driver Board?

by SomeoneKnows
1,456 2 02/06/2008 09:48AM
Last Post by ZachHoeken

Nichrome res reading?

by Dylan
1,584 7 02/06/2008 12:40AM
Last Post by Dylan

Problems using 5 pin stepper motors

by greenarrow
2,701 8 02/02/2008 06:24PM
Last Post by greenarrow

16f648a

by Dylan
1,971 5 01/31/2008 07:38PM
Last Post by Dylan

No Extruders Attached!

by Demented Chihuahua
1,264 6 01/31/2008 03:44AM
Last Post by Demented Chihuahua

555 oscillator for thermistor instead of divider?

by Triffid_Hunter
2,760 4 01/23/2008 07:22AM
Last Post by nophead

Troubleshoot Power Comms 1.3 Board

by Squintz
1,572 7 01/21/2008 07:11PM
Last Post by Demented Chihuahua

Making Cables 2 Pin Housing/Crimps

by Squintz
1,602 2 01/21/2008 02:29PM
Last Post by Ian Adkins

UCB promlem.... again   (Pages: 1 2)

by Dylan
3,644 45 01/20/2008 12:48PM
Last Post by Dylan

Cheap optopstop alternative

by Joost
1,705 7 01/17/2008 04:24PM
Last Post by ZachHoeken

Electric motor supplies

by Charley
1,697 5 01/16/2008 06:50PM
Last Post by Charley

Semi-Industrial RepRap Board Design Question: Card Edge or Pin Header?

by SOI Sentinel
2,613 8 01/16/2008 04:09PM
Last Post by Assargadon

Host & Arduino Electronics

by emt
1,813 6 01/11/2008 09:20PM
Last Post by ZachHoeken

amateurifying the PCB's Attachments

by mimarob
1,627 3 01/07/2008 12:28PM
Last Post by mimarob

Validation of Arduino based electronics

by bobt
1,811 10 01/04/2008 10:35PM
Last Post by bobt

Parts website recommends PIC-PG3

by RoundSparrow
1,677 8 01/04/2008 10:24AM
Last Post by degroof

Single_Arduino - Extruder heater voltage

by RoundSparrow
1,480 4 12/30/2007 10:04PM
Last Post by ZachHoeken

DC motors + RepRap + Arduino

by roypardi
3,460 5 12/30/2007 03:18PM
Last Post by ZachHoeken

Arduino Single_Arduino_Snap.pde environment

by RoundSparrow
1,842 5 12/27/2007 12:31PM
Last Post by bobt

Testing electronics, wires, etc.

by RoundSparrow
1,570 3 12/27/2007 12:14PM
Last Post by ZachHoeken

Stepper Driver v1.1 - Sync wires between boards

by RoundSparrow
2,259 11 12/27/2007 12:08PM
Last Post by ZachHoeken

TX/RX problem [solved]

by Dylan
1,910 8 12/25/2007 08:57PM
Last Post by Dylan

Which RepRap?

by Squintz
2,021 5 12/25/2007 07:50PM
Last Post by jmarsden

Easy home-position-calibration with a web-cam Attachments

by VDX
2,054 3 12/23/2007 04:21PM
Last Post by VDX

Getting free samples

by flaex
1,424 1 12/18/2007 12:20PM
Last Post by flaex

Questions about the stepper motors

by reece.arnott
1,312 5 12/18/2007 12:53AM
Last Post by reece.arnott