Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

Low voltage on power supply

by Kyle Corbitt
1,411 6 09/01/2007 01:19AM
Last Post by Richard

Questions and comments about Stepper and Extruder boards

by reece.arnott
1,580 4 08/30/2007 12:33PM
Last Post by nophead

premade cables

by Anonymous User
2,143 10 08/29/2007 05:15PM
Last Post by d0ubled

Layout software help

by therapy
1,266 2 08/28/2007 10:33AM
Last Post by ZachHoeken

Still Stuck on UCB

by TimmyH79
1,361 6 08/23/2007 09:30AM
Last Post by ZachHoeken

Output from UART chip to PWM circuit

by NBostan
2,706 2 08/21/2007 06:25AM
Last Post by nophead

Universal Controller v1.3.0

by ZachHoeken
1,769 20 08/18/2007 10:22AM
Last Post by ZachHoeken

Testing PowerComms

by emt
1,500 9 08/13/2007 03:51AM
Last Post by nophead

First impressions of Stepper Tester and Stepper Board

by reece.arnott
1,386 2 08/12/2007 03:30PM
Last Post by ZachHoeken

temperature swinging   (Pages: 1 2)

by Anonymous User
3,098 44 08/11/2007 05:46AM
Last Post by nophead

A question about the RS22 cable

by Ron Luttik
1,908 2 08/07/2007 03:36PM
Last Post by nophead

Nichrome wire Ohms clarification

by Richard
1,344 6 08/06/2007 08:12AM
Last Post by nophead

Dead link for the opto-endstop

by Forrest Higgs
1,322 4 08/05/2007 11:47PM
Last Post by jmarsden

USB stepper motor control.

by Anonymous User
1,680 1 08/03/2007 12:46PM
Last Post by d0ubled

PowerComms v1.3.0

by ZachHoeken
1,276 11 08/02/2007 05:03PM
Last Post by ZachHoeken

ANother UCB issue

by TimmyH79
1,309 14 08/02/2007 03:59PM
Last Post by emf

Powercomms board first impressions

by reece.arnott
1,341 2 08/02/2007 01:08PM
Last Post by ZachHoeken

Universal Controller Rx & Tx

by emt
1,157 5 08/02/2007 12:56PM
Last Post by ZachHoeken

PowerComms Voltages

by Anonymous User
1,150 2 08/02/2007 10:06AM
Last Post by englewood

Extruder thermistor

by nophead
1,441 7 08/01/2007 04:03PM
Last Post by ZachHoeken

picaxe?

by yeahgday
1,760 8 07/31/2007 12:48PM
Last Post by ZachHoeken

Eagle format or KiCad -> Eagle howto?

by Colin K.
9,422 5 07/31/2007 12:14AM
Last Post by Colin K.

DIY Servo

by Joost
1,727 1 07/30/2007 03:45PM
Last Post by Joost

Substitutions

by Richard
1,612 6 07/29/2007 08:03PM
Last Post by Richard

Electronics problem?

by Joost
1,697 11 07/29/2007 07:48PM
Last Post by englewood

PowerComms + Programmer

by ZachHoeken
2,127 30 07/28/2007 06:14PM
Last Post by TimmyH79

Testing UCB

by emt
1,127 2 07/26/2007 07:54PM
Last Post by jmarsden

Parts List   (Pages: 1 2)

by R I Eagland
2,393 38 07/22/2007 03:12PM
Last Post by emf

UCB Test Instructions modified

by jmarsden
1,195 1 07/22/2007 12:30AM
Last Post by jmarsden

'Sync' connection on the stepper controllers?

by Anonymous User
1,304 9 07/21/2007 01:29PM
Last Post by jmarsden