Welcome! Log In Create A New Profile

Advanced

Mechanics

Discuss any sort of mechanical stuff here: positioning systems, gears, extruding methods, etc. 
Page 5 of 39    Pages: FirstPrevious34567NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

Nema 08 via ramps 1.4?

by panterateama 		1,604 4 12/12/2018 06:45AM
Last Post by the_digital_dentist

Improvement on Thermistor mount and wire management!!!

by rossfree 		1,369 7 12/09/2018 04:12PM
Last Post by MKSA

using non-idler pulleys as idlers directly on the shaft - no bearings

by ag123 		3,522 10 12/05/2018 03:54PM
Last Post by dc42

Power Wiring Attachments

by blt3dp 		4,392 26 12/02/2018 09:20PM
Last Post by PDBeal

SoM Y axis rebuild

by the_digital_dentist 		1,551 5 11/26/2018 03:18PM
Last Post by Ed3D

Mounting linear rails on plywood/acrylic/whatever?

by ruyvieira 		1,982 20 11/15/2018 04:27PM
Last Post by warbunniex

Corexy (or similar) with extened x-axis

by Pilot65 		1,932 11 11/11/2018 09:08PM
Last Post by ruyvieira

kraken autolift hotend Attachments

by Joar107 		3,841 9 11/08/2018 03:43AM
Last Post by evandene

Looking for 1.75mm nozzle with 1.85mm input diameter

by lukie80 		1,318 7 10/23/2018 08:27AM
Last Post by Srek

upgrading printer

by Blisk 		1,448 6 10/06/2018 05:24PM
Last Post by cozmicray

Replace timing belts with FireLine Attachments   (Pages: 1 2 3 4 5)

by j0achim 		9,769 126 10/06/2018 02:23AM
Last Post by o_lampe

E3d v6 chimera dual extruder single nozzle problem?

by malio77 		1,258 1 10/04/2018 08:45AM
Last Post by malio77

Advice for the self-construction of a printer and lasagne with chamomile.. eye rolling smiley

by Pinguto 		895 8 09/30/2018 12:37PM
Last Post by the_digital_dentist

Fan needed at all if not printing with PLA

by JacksonBenz 		4,083 7 09/25/2018 08:01AM
Last Post by Roberts_Clif

Diamond Hotend thermal insulation sheet - alternatives   (Pages: 1 2)

by zylantha 		5,233 31 09/11/2018 08:07AM
Last Post by MechaBits

Where to get something like this ?

by Arnix 		1,010 8 09/11/2018 03:49AM
Last Post by Arnix

help me identify this leadscrew? Attachments

by merlin777 		924 5 08/23/2018 05:01PM
Last Post by Roberts_Clif

Linear Guide too tight

by JoergS5 		1,809 7 08/07/2018 04:23PM
Last Post by JoergS5

Mk8 extruder calibration problem (overextruded)

by barisali77 		895 3 08/06/2018 01:43PM
Last Post by barisali77

spring steel 400mm x 400mm

by bbcbggr54 		1,444 2 08/06/2018 01:52AM
Last Post by ekaggrat

Print bed Aluminium plate W28, EN AW 5083

by JoergS5 		1,778 4 08/03/2018 05:52AM
Last Post by JoergS5

Lubricating Guide Carriages Attachments

by VectorRoll 		3,176 6 07/15/2018 07:06AM
Last Post by JoergS5

Layer line annealing in place during print

by Infallibel 		864 3 07/09/2018 06:07PM
Last Post by Infallibel

Correct way to interface braided line with stepper motor?

by Ohmarinus 		2,153 12 07/07/2018 04:21PM
Last Post by Ohmarinus

Anet A8 Rumba Upgrade: Problem with Sensorless Homeing Attachments

by citrullin 		1,355 1 07/06/2018 04:49PM
Last Post by citrullin

Choose my upgrade!

by cubeconvict 		1,560 5 07/03/2018 11:51PM
Last Post by Trakyan

what is fan holder for this type ultimaker extruder clone? eye rolling smiley

by AhmedU 		808 9 06/23/2018 07:44AM
Last Post by AhmedU

Seems impossible to find quality GT2 20T 5mm Pulleys

by DivePADI 		1,698 3 06/20/2018 07:58AM
Last Post by the_digital_dentist

Staged heating extruder

by Infallibel 		1,019 8 06/15/2018 07:40AM
Last Post by deckingman

Zwei hotends einstellen Hardware und in Marlin

by Norbert P 		680 3 06/14/2018 07:55AM
Last Post by Norbert P
Page 5 of 39    Pages: FirstPrevious34567NextLast