Welcome! Log In Create A New Profile

Advanced

Firmware - experimental, borrowed, and future

Subject Views Posts Last Post

M42 on pwm pin only outputs 5V or 0V

by heyisaacsback
875 4 04/12/2016 12:40PM
Last Post by Wurstnase

MArlin not uploading

by Shogun
418 2 04/10/2016 01:49AM
Last Post by Dust

Marlin with DC Motor for Extruder

by jmiller451
870 3 03/24/2016 06:52PM
Last Post by jmiller451

More fan and sensors?

by Vuokko
563 2 03/12/2016 03:50PM
Last Post by dc42

Permissive Licenced Firmware???

by PauloAndrade
592 3 03/07/2016 06:26AM
Last Post by PauloAndrade

Simultaneous E1 and E0 printing Marlin

by 3dprinting01
1,027 4 03/02/2016 05:00PM
Last Post by Julio C

Marlin firmware displaying remaining time on LCD

by dominate
1,408 2 02/21/2016 03:41AM
Last Post by dc42

Filament Change Marlin ver2.2 issue

by masteffen
802 1 02/09/2016 11:29PM
Last Post by masteffen

Analog Read in Marlin - Right Way Too Read

by jasane
793 2 01/20/2016 03:06AM
Last Post by Wurstnase

LCD support

by cheezus
804 1 01/11/2016 08:13PM
Last Post by cheezus

Building a concrete 3D printer - need help with movement

by mekastudios
793 3 12/16/2015 07:23AM
Last Post by mekastudios

Edited [Kossel Mini] ABL not working on Marlin1.1.0RC2 probing out of printbed

by Culain
2,011 3 11/17/2015 09:37AM
Last Post by nebbian

Marlin with Azteeg X3 and thermocouple sensor Attachments

by cuongvd
2,947 8 10/17/2015 09:06PM
Last Post by laernmoer

[TeaCup Firmware] : to add a fan control

by jojolapatade
2,471 17 10/13/2015 06:21AM
Last Post by Traumflug

Losing X axis and Y axis coordinates during printing at Marlin Firmware

by jasane
1,178 2 09/29/2015 06:59AM
Last Post by Dust

Repetier firmware diferent step for mm

by sandro730
1,130 1 09/22/2015 08:21AM
Last Post by sandro730

Marlin - Configure Serial 0 and Serial 2

by rbastini
1,784 1 09/15/2015 08:31AM
Last Post by rbastini

Modifying Prusa i3 for syringe pump

by gkoshy
1,208 1 09/09/2015 12:32PM
Last Post by gkoshy

Directional Control

by aleroux2015
1,289 1 08/18/2015 01:26AM
Last Post by aleroux2015

Leveling mode to move extruder to four corners

by ronhogwarts
1,398 1 07/19/2015 08:46AM
Last Post by ronhogwarts

Adding a custom G-Code case in firmware Marlin

by kasper219
2,359 4 07/07/2015 04:59PM
Last Post by jessicabrenner

Teacup on Sanginololu under Win 7 Attachments   (Pages: 1 2)

by OSUFlatland
2,498 41 07/03/2015 07:59PM
Last Post by OSUFlatland

Getting more speed out of Arduino Mega

by TESKAn
1,896 15 06/24/2015 08:43AM
Last Post by Wurstnase

Raise extruder on stop print

by casperen
1,680 1 06/16/2015 12:27PM
Last Post by casperen

reading gcode file from sdcard in cpp other than using gcodes

by prasunjoshi
1,475 2 06/16/2015 02:41AM
Last Post by thetazzbot

Curved paths

by frankvdh
2,059 18 05/28/2015 07:29PM
Last Post by frankvdh

Leveling a particular area based off the current print's size

by kasper219
1,505 4 05/22/2015 08:45AM
Last Post by Wurstnase

Teacup_Firmware: How can i add other board to the firmware?

by tatubias
2,225 2 05/19/2015 11:46AM
Last Post by tatubias

manage_heater not updated during long moves

by Gosa
1,454 6 05/16/2015 06:47PM
Last Post by dc42

Adding support for up to 16 added temp sensors???

by kasper219
1,551 4 05/09/2015 12:16PM
Last Post by kasper219