Welcome! Log In Create A New Profile

Advanced

Firmware - experimental, borrowed, and future

Subject Views Posts Last Post

marlin(arduino mega) strange G code explanations Attachments

by hihijudy
2,121 1 05/05/2015 07:58AM
Last Post by hihijudy

Teacup - temperature control and safety

by mogul
2,078 1 05/02/2015 08:41AM
Last Post by mogul

Arduino MEGA 2650 Temperature overhead

by Smart
2,061 6 04/30/2015 07:48AM
Last Post by Smart

Firmware architecture question trajectory planning

by nilrods
2,464 9 04/22/2015 01:28PM
Last Post by ambrop7

Assigning a new pin for the controller fan

by oscarte
2,190 1 04/21/2015 01:45PM
Last Post by oscarte

manual one dir Y axis

by vangalvin
2,123 1 04/18/2015 12:17PM
Last Post by vangalvin

Including Mechanical Brake in Marlin-Software on RUMBA Board

by karl.ranseier
2,650 2 04/09/2015 07:45AM
Last Post by karl.ranseier

Problem temperature keeps raising

by Donato
1,996 1 04/08/2015 06:34PM
Last Post by Donato

Uarm based 3D printer

by tomfrombelgium
1,859 3 04/02/2015 02:03PM
Last Post by ekaggrat

What is the first file called when Marlin begins printing?

by Evil Monkey
2,097 6 03/29/2015 09:25PM
Last Post by Evil Monkey

Including Quadrature Encoder - PID positioning of DC motors into Teacup_Firmware

by unix_guru
3,075 4 03/27/2015 08:06AM
Last Post by unix_guru

borrowed (thermistor for toaster reflow) need help

by terramir
2,120 7 03/26/2015 01:33PM
Last Post by dc42

Marlin 32bit high step_rate

by Wurstnase
3,069 12 03/24/2015 01:14PM
Last Post by Wurstnase

start filament rejection Attachments

by lolohtl
1,890 1 03/22/2015 03:59PM
Last Post by lolohtl

Looking for an easily modifiable 'bare-bones' firmware.

by Capo
1,697 10 03/08/2015 06:57AM
Last Post by Capo

Changing bay on RUMBA motion controller for Extruder Stepper Driver

by SkiBum326
1,915 2 03/07/2015 11:23PM
Last Post by cat.farmer

Marlin 1.03 appeared and disapeared

by gordonendersby
1,749 2 03/06/2015 02:41PM
Last Post by gordonendersby

Help adding push button input to jog/ retract extruder for RAMPS

by alan richard
2,630 3 03/06/2015 12:08PM
Last Post by alan richard

Marlin Error:Thermal Runaway, system stopped! Heater_ID: 9

by Miamicraft
3,148 1 03/01/2015 06:41PM
Last Post by Miamicraft

bariCUDA Paste Extruder Support, Marlin

by jessicabrenner
2,166 1 02/24/2015 03:26AM
Last Post by jessicabrenner

Marlin endstop read

by luismanson
1,384 3 02/22/2015 03:11PM
Last Post by luismanson

I'm looking for a PostProcessor for SprutCam, that will output Gcode for Marlin

by dailafing
1,761 4 02/22/2015 07:24AM
Last Post by Traumflug

Help needed compiling Teacup_Firmware_Teensy3

by unix_guru
1,431 5 02/12/2015 05:00PM
Last Post by Traumflug

how change pins of full graphic smart controller in repetier firmware.

by snype
1,673 1 01/22/2015 05:56PM
Last Post by snype

G-code explanation

by calogerom
1,860 8 12/27/2014 12:16AM
Last Post by jbernardis

Something about PIN in Reprapfirmwareconfused smiley

by sevenljy
1,366 4 12/24/2014 04:54AM
Last Post by dc42

Marlin Probe Configuration

by jmarasch
1,513 1 12/03/2014 10:50AM
Last Post by jmarasch

serial port illegible

by takluiper
1,330 3 12/02/2014 02:15PM
Last Post by calogerom

Unused Digital Pins

by donhuevo
6,562 6 11/28/2014 10:23AM
Last Post by donhuevo

Modifying Firmware for different printing methods

by piscosour00
1,872 3 10/08/2014 05:36PM
Last Post by unlimitedbacon