Welcome! Log In Create A New Profile

Advanced

General Mendel Topics

Prusa i2, Prusa i1, Prism, Sells, and other Mendel variants 
Subject Views Posts Last Post

Prusa Mendel Z axis doesnt work

by B3nki
2,403 3 08/25/2021 01:58PM
Last Post by shady0248

MK3 Alu-Heatbed how to print with a hole in center.

by Carlos Fellip
2,813 6 06/25/2021 01:16PM
Last Post by ag123

RepRapPro Mendel 3 - printable parts

by nanotone
1,046 2 06/06/2021 03:14PM
Last Post by Gaou

RepRap iTopie - A Prusa i3 evolution - Development discussion   (Pages: 1 2)

by skarab
19,136 43 02/20/2021 04:15PM
Last Post by NovaHuta

Prusa i3 mandel

by yar60
1,238 2 02/12/2021 05:05AM
Last Post by Dust

New heat bed for Orcabot 0.4 Attachments

by NozzleMover
1,358 1 12/07/2020 08:24AM
Last Post by NozzleMover

I need your help about the board MK808B Clone eye popping smiley Attachments

by ADRIANO3D
5,507 13 12/04/2020 06:03AM
Last Post by giuly

RepRap Samuel - A variation on the Mendel   (Pages: 1 2 3 4)

by silpstream
20,928 110 10/30/2020 06:55AM
Last Post by AlienKnalKoe

Kapton forming bubbles under print

by mlaustin66
3,386 11 09/28/2020 05:17PM
Last Post by Keveeeeeee

Strange loud buzz before homing normally Attachments

by villainousindustries
2,330 8 06/02/2020 01:34PM
Last Post by Justinjjhcs1

Buzzing steppers when homing

by cmerce
3,616 7 06/02/2020 04:06AM
Last Post by MKSA

Gen 6 delux electronics - Programm with ISP

by NozzleMover
2,014 2 05/27/2020 03:36AM
Last Post by NozzleMover

Attempting to print above bed. Attachments

by TerryD15
2,261 1 03/12/2020 04:32AM
Last Post by TerryD15

My printer is set up with the nozzle offsets and when the printer homes the nozzle is just right. The Attachments

by TerryD15
2,248 3 03/12/2020 02:11AM
Last Post by TerryD15

Z axis not lowering Attachments

by TerryD15
2,382 2 03/10/2020 11:24AM
Last Post by TerryD15

Prusa i3 Isee Board, Needs Firmware urgent! please smiling smiley Attachments

by edisonpaul4
5,376 6 12/18/2019 05:32PM
Last Post by poggia10

Here is my Prusa i3 !   (Pages: 1 2)

by franck
20,003 43 10/26/2019 05:51AM
Last Post by Ohmarinus

How to recycle a ReprRapPro MENDEL

by Jef_Lord
3,725 6 08/01/2019 08:49AM
Last Post by Jef_Lord

Project log: Air 2 upgrade

by Ohmarinus
3,727 4 04/03/2019 03:02PM
Last Post by Ohmarinus

Strange lumpiness after print is about 1cm high Attachments

by davies46
3,129 4 03/24/2019 06:19AM
Last Post by MotoBarsteward

Advice on Firmware/Software and Extruder

by Adam.m.Nelson
3,312 4 03/18/2019 03:15PM
Last Post by dlc60

printrbot printrboard Rev. D

by ola
3,312 2 01/21/2019 09:50AM
Last Post by Dust

my prusa i2 is stalling on the Z changed stepper driver and greased screws

by terramir
3,506 6 11/27/2018 09:44AM
Last Post by Roberts_Clif

Dimension error in Z

by ChicoCyberGoth
3,343 12 10/31/2018 11:39AM
Last Post by blt3dp

Problem with X carriage and extruder Attachments

by ChicoCyberGoth
3,130 1 10/27/2018 10:18PM
Last Post by ChicoCyberGoth

Anet A8 Homing Issues

by punker970
3,146 2 10/27/2018 02:26AM
Last Post by jefbed

Getting the bits? Prusa Mendel

by aamcle
3,557 6 10/16/2018 05:57AM
Last Post by jefbed

Prusa i2 Axis not moving giving a jerk sound and stopping

by kptroy09
3,239 12 10/15/2018 02:36PM
Last Post by kptroy09

Had enough with CubeX, looking for reprap migration confused smiley Attachments

by duckfriedrice
11,767 13 09/29/2018 02:56AM
Last Post by MKSA

Prusa I2 for laser etching Attachments

by Shank man
4,281 7 09/09/2018 01:37PM
Last Post by Shank man