Welcome! Log In Create A New Profile

Sanguino(lolu)

The Sanguino is an extension of the popular Arduino board designed and developed by Zach Hoeken et.al. for the RepRap Research Foundation.

Page 6 of 15 Pages:

4 567 8

Forum List New Topic RSS

	Views	Posts	Last Post
Opto endstops and Marlin on Delta printer by slorite	3,970	8	11/02/2013 07:43PM Last Post by slorite
end stops (Marlin) not registering?! by [email protected]	968	5	10/26/2013 09:50PM Last Post by hcker2000
Sanguinololu not working standalone by ax2013	1,063	2	10/25/2013 03:18PM Last Post by ax2013
Board hangs by andreykyz	866	2	10/13/2013 08:00PM Last Post by frontier204
using a second sanguinolulu to expand extruders by prof111	1,203	3	09/24/2013 09:33AM Last Post by prof111
End Stop Issue , mechanical end stop 1.2 by xblack0	1,081	2	09/24/2013 08:11AM Last Post by slymike
Hotend always on by Scaf_13	907	1	09/18/2013 10:05AM Last Post by Scaf_13
Heatsink shorted pololu, sanguino can no longer connect by Candar	1,105	5	09/11/2013 07:36PM Last Post by Candar
Sanguinololu: Sanguino + Pololus - Rev 0.7 (Pages: 1 2) by joe m	9,024	52	09/07/2013 04:56AM Last Post by papakel
gen3 Temperature.h:331: error: 'bedtemptable' was not declared in this scope by hellorous	852	2	09/06/2013 07:33AM Last Post by Traumflug
Connecting Problems Prusa i3 with Sanguinololu by Mechanic	2,233	6	09/05/2013 05:23PM Last Post by papakel
Problem with Power Supply by arget888	1,232	5	08/30/2013 07:34AM Last Post by arget888
Hotend Problem by loverton	784	2	08/29/2013 08:10AM Last Post by Dust
Endstops pullup resistors always low by Eddie4	1,358	4	08/23/2013 04:09PM Last Post by Eddie4
Using extra IO ports in Marlin? by dnhkng	4,635	8	08/09/2013 10:35AM Last Post by slymike
What Software do I need? by jrz126	828	3	08/08/2013 01:25AM Last Post by tenbaht
Sanguinololu 1.3a X axis stepper motor shaky movement by ahuddart	1,307	2	08/03/2013 07:42AM Last Post by Dust
Sanguinololu homing/end stop problems by nicoowtje	2,896	6	08/03/2013 12:36AM Last Post by flurin
prevent usb 5V backfeeding by Stemer114	11,011	17	08/02/2013 11:44AM Last Post by pokey9000
help with twitching steppers by Hallestman	896	7	07/31/2013 10:02AM Last Post by Hallestman
Why are end stops NO instead of NC? by Dschiri1	2,298	3	07/27/2013 04:36AM Last Post by tenbaht
Panelou & Sanguino setup ? by Mickman	1,397	7	07/23/2013 04:43AM Last Post by Mickman
Thermistors reading high by leadinglights	1,376	3	07/16/2013 01:49AM Last Post by aimbug
Help Fixing a Sanguinololu After Mistake by danfinlay	1,525	5	07/15/2013 09:52AM Last Post by lajos
Endstop don't work, when more than one endstop are connected by metalzse	954	2	07/12/2013 04:22PM Last Post by metalzse
Sanguinololu 1.3a 1284p - no power at heatbed. by Ziomboj7	1,556	6	07/02/2013 04:48PM Last Post by Ziomboj7
Can Sanguinololu 1.3A control 12V 200W heated bed ? by zacman	2,547	6	07/01/2013 10:59AM Last Post by lajos
Burning Sanguino bootloader onto 1284p onboard using arduino mega by freemoore	10,018	6	06/26/2013 10:21AM Last Post by GowthamJGR
Resonator 16.00MHZ vs Crystals 16MHz by raymond3080	2,777	8	06/26/2013 10:11AM Last Post by GowthamJGR
Pins.h in Marlin Firmware by GowthamJGR	4,169	4	06/25/2013 10:38AM Last Post by GowthamJGR

Page 6 of 15 Pages:

4 567 8

Sanguino(lolu)

Sanguinololu: Sanguino + Pololus - Rev 0.7 (Pages: 1 2)