Welcome! Log In Create A New Profile

Advanced

Stepper Motors, Servo Motors, DC Motors

Discuss here what makes your printer moving. 
Subject Views Posts Last Post

Calculating stepper driver settings

by brucehvn
648 3 10/22/2018 04:33AM
Last Post by brucehvn

A4988 and 1/8 step resolution MightyBoard.

by aamcle
495 1 10/18/2018 05:23PM
Last Post by aamcle

Solid State Relays / Question to the experts Attachments

by elvis
469 4 09/12/2018 10:44AM
Last Post by elvis

Z Motors turning on retract/unretract

by brucehvn
284 2 09/09/2018 06:36PM
Last Post by brucehvn

Leadshine hybrid servo vs Mechaduino

by vader333
387 1 08/29/2018 02:39AM
Last Post by vader333

Powering TMC2208 with external 24V PSU

by Kespa
546 3 08/28/2018 04:35PM
Last Post by Kespa

How to tune again my a4988

by Aldebaran94
578 9 07/21/2018 02:47AM
Last Post by o_lampe

Print just stopped, motor/stepper driver issue?

by Gaz83
292 6 07/19/2018 05:16PM
Last Post by Gaz83

Stepper driver for titan aero extruder

by Gaz83
708 5 07/17/2018 05:22PM
Last Post by Gaz83

MKS LV8729 , a 128 ┬ÁStep Driver // Any test?   (Pages: 1 2)

by epoxi
24,357 37 07/14/2018 08:18AM
Last Post by banzaito

Correct calculation for TMC2100 vref

by Gaz83
1,132 5 07/13/2018 08:06AM
Last Post by Gaz83

Would moving from A4988 to TMC2130+ improve/affect print quality?

by Lobotomy
763 10 07/12/2018 02:12PM
Last Post by LB

TMC 2130 Love-Hate Relation Attachments

by Banana_Luke
5,572 16 06/27/2018 09:08PM
Last Post by Bartje64

Testing rig for stepper drivers?

by jemenake
423 3 06/27/2018 07:09PM
Last Post by hotbutteredhtml

Mks steppers

by nod2
411 1 06/12/2018 09:07AM
Last Post by nod2

Source for brackets with 25mm on-center slots instead of 30?

by gtj
415 4 05/16/2018 11:47AM
Last Post by gtj

Calculating current with Vref pin (a4982, a4988, a5984)

by asrt
1,734 4 05/12/2018 02:54AM
Last Post by o_lampe

Linear stepper motors   (Pages: 1 2 3)

by klcjr89
2,914 76 04/29/2018 11:27AM
Last Post by klcjr89

[solved] MKS LV8729 drivers only working when at least one A4988 present on board

by Fivefold
939 3 04/28/2018 06:18PM
Last Post by Fivefold

Stepper motor info & tuning

by cwyse
1,373 1 04/22/2018 09:56AM
Last Post by cwyse

Need help finding drivers to match to my steppers

by chrisg9
476 8 04/14/2018 05:13PM
Last Post by chrisg9

stepper motors requiring more steps than it should

by nick9one1
404 2 03/29/2018 03:55AM
Last Post by o_lampe

e3d Titan extruder steps per mm settings don't do anything

by fullHundo
3,753 6 03/19/2018 04:19AM
Last Post by o_lampe

What is this connector called?

by fullHundo
385 3 03/18/2018 02:46PM
Last Post by fullHundo

RUMBA: stepper (&power) selection

by joaogatao
483 2 02/08/2018 06:28AM
Last Post by VDX

Cheapest nema 17

by Falcondestroyer123
562 7 02/01/2018 09:41PM
Last Post by obelisk79

current controlled DC motor by e-steps?

by o_lampe
505 1 01/25/2018 05:57AM
Last Post by o_lampe

extruder working but not XYZ

by Soundtrackzz
394 2 01/18/2018 08:53PM
Last Post by Dust

How do diagnose RUMBA board not moving extruder motor

by bolsoncerrado
1,982 20 12/29/2017 08:16PM
Last Post by Dust

TMC2100 driving dual Z - thermal shutdown?

by 3dflat
1,067 5 12/29/2017 04:11AM
Last Post by dc42