Welcome! Log In Create A New Profile

Advanced

Stepper Motors, Servo Motors, DC Motors

Discuss here what makes your printer moving. 
Subject Views Posts Last Post

For the low-voltage steppers we use, is a low-voltage driver like DRV8834 more appropriate?

by Pointedstick
438 5 10/13/2016 07:44AM
Last Post by the_digital_dentist

TMC2100 V-Ref Troubles

by jared248371
429 1 10/04/2016 11:54AM
Last Post by jared248371

Auto bed leveling servo issue

by Stoica
287 1 09/30/2016 06:31PM
Last Post by Stoica

powerlolu ordering Attachments

by yoyobob19
1,760 18 09/26/2016 10:58PM
Last Post by yoyobob19

Current for a Printer with 5 Nema17 Steppers

by MilloMille
451 7 09/25/2016 02:33PM
Last Post by dc42

Advice on motors for c-bot.

by ian_in_the_midlands
2,004 8 09/16/2016 01:10PM
Last Post by hucilu

How do I control a Japan Servo Co., Ltd stepper? Attachments

by jenjenjen
636 3 09/15/2016 07:45PM
Last Post by jenjenjen

Issue with cncshield+arduino. Steppers stopped working.

by jvales
282 1 09/13/2016 06:24AM
Last Post by jvales

1 Stepper Motor, Uno R3, CNC, power supply question

by Cmmain
1,157 10 08/30/2016 07:29AM
Last Post by NoobMan

Stepper Moving in Bigger Steps FORWARD than BACKWARD

by SJMaybury
261 5 08/29/2016 06:54PM
Last Post by SJMaybury

Help needed for selecting driver

by hyunwoop
300 2 08/29/2016 04:49PM
Last Post by SJMaybury

Nema 17 operating at 60°C - still ok?

by Persephone
1,010 2 08/29/2016 04:46PM
Last Post by SJMaybury

Interpreting Stepper Specs: Inductance, Etc.

by UncleSas
985 7 08/28/2016 10:58PM
Last Post by UncleSas

Thinking about increasing motor voltage

by Vuokko
331 3 08/23/2016 04:07PM
Last Post by o_lampe

Question about behaviour of stepper motors in manual mode

by mamech
295 5 08/22/2016 10:12AM
Last Post by mamech

stepper wiring

by MechaBits
402 7 08/16/2016 01:55PM
Last Post by MechaBits

"Newbie" Can someone point me in the right direction?

by Dakwally
313 4 08/08/2016 04:52PM
Last Post by cozmicray

Which steppers for DIY Ultimaker 2?

by harmaasilmä
884 14 08/08/2016 06:19AM
Last Post by harmaasilmä

Use E1 driver on Rambo for independent Z levelling?

by aegidius
256 2 08/07/2016 03:04AM
Last Post by o_lampe

Stepper motors increase speed when touched.

by snorrus
291 2 07/28/2016 01:39PM
Last Post by o_lampe

Motors only turning one way

by Aschie4589
691 9 07/26/2016 12:00PM
Last Post by Aschie4589

Need help with servo end stop on Rambo 1.3

by ronnien55
360 2 07/24/2016 08:56AM
Last Post by ronnien55

Help with calculating the speed required for motors

by kelly27
225 2 07/13/2016 10:03PM
Last Post by Dust

Nokia 5110 LCD for ramps

by Danny141
478 1 07/10/2016 12:35PM
Last Post by Danny141

[Solved] Z low torque with TMC2100 driver during Going-home

by Arteriel
950 3 07/08/2016 04:40AM
Last Post by dc42

Issues with Stepper

by Ma_tits
329 8 07/05/2016 01:02PM
Last Post by the_digital_dentist

Whats needed to run nema 23's?

by The Borg
1,096 2 07/03/2016 10:02PM
Last Post by the_digital_dentist

Issue with motor or Firmware

by samotras
271 2 06/22/2016 02:00PM
Last Post by o_lampe

Stepper motors with 7.5deg steps?

by heimerdinger
2,607 8 06/22/2016 09:20AM
Last Post by kestux75

Can't get enough steps or maybe power

by triggernom
280 4 06/08/2016 01:18PM
Last Post by triggernom