Welcome! Log In Create A New Profile

Advanced

Stepper Motors, Servo Motors, DC Motors

Discuss here what makes your printer moving. 
Subject Views Posts Last Post

"Newbie" Can someone point me in the right direction?

by Dakwally
348 4 08/08/2016 04:52PM
Last Post by cozmicray

Which steppers for DIY Ultimaker 2?

by harmaasilmä
1,014 14 08/08/2016 06:19AM
Last Post by harmaasilmä

Use E1 driver on Rambo for independent Z levelling?

by aegidius
284 2 08/07/2016 03:04AM
Last Post by o_lampe

Stepper motors increase speed when touched.

by snorrus
321 2 07/28/2016 01:39PM
Last Post by o_lampe

Motors only turning one way

by Aschie4589
783 9 07/26/2016 12:00PM
Last Post by Aschie4589

Need help with servo end stop on Rambo 1.3

by ronnien55
404 2 07/24/2016 08:56AM
Last Post by ronnien55

Help with calculating the speed required for motors

by kelly27
258 2 07/13/2016 10:03PM
Last Post by Dust

Nokia 5110 LCD for ramps

by Danny141
531 1 07/10/2016 12:35PM
Last Post by Danny141

[Solved] Z low torque with TMC2100 driver during Going-home

by Arteriel
1,046 3 07/08/2016 04:40AM
Last Post by dc42

Issues with Stepper

by Ma_tits
366 8 07/05/2016 01:02PM
Last Post by the_digital_dentist

Whats needed to run nema 23's?

by The Borg
1,441 2 07/03/2016 10:02PM
Last Post by the_digital_dentist

Issue with motor or Firmware

by samotras
302 2 06/22/2016 02:00PM
Last Post by o_lampe

Stepper motors with 7.5deg steps?

by heimerdinger
2,928 8 06/22/2016 09:20AM
Last Post by kestux75

Can't get enough steps or maybe power

by triggernom
305 4 06/08/2016 01:18PM
Last Post by triggernom

interesting quirks with feedrate and new motor drivers.

by mrsour
421 2 06/08/2016 10:39AM
Last Post by mrsour

Identifing a damaged stepper

by Gaou
312 1 06/02/2016 12:57PM
Last Post by Gaou

how do i stop the motor shaft which has a load, from rotating when the power is shut off

by za
360 7 05/30/2016 11:01AM
Last Post by the_digital_dentist

Very jerky stepper movement

by Jelby-John
3,623 20 05/27/2016 10:24PM
Last Post by BioLumo

Resisting Voltage from Power Stage

by sullivnc
242 3 05/25/2016 03:07PM
Last Post by bobc

Voltage Rumba board

by Hans123456789
496 1 05/19/2016 08:01AM
Last Post by Hans123456789

Vibration at low speed

by Nikel
1,600 6 05/18/2016 06:16PM
Last Post by the_digital_dentist

Choice between two steppers

by jonawald
319 1 05/12/2016 12:03AM
Last Post by jonawald

C Driver not fully working

by Nikel
203 2 05/06/2016 05:09AM
Last Post by bobc

Help with Project List

by jr9820
236 4 05/04/2016 11:17PM
Last Post by cozmicray

DRV8825 "skipping" microsteps

by peepsalot
7,001 8 05/04/2016 04:55PM
Last Post by MrBaz

Stepper motor power supply

by Harmsobuk
2,228 4 04/27/2016 09:56AM
Last Post by the_digital_dentist

Stepper Motors from old Laser Printers

by nike357
2,010 14 04/26/2016 02:24AM
Last Post by nike357

Speed and torque calculation of stepper motor Attachments

by bobdxcool
2,896 2 04/23/2016 06:11PM
Last Post by dc42

Prusa i3 steppers

by Stoica
280 3 04/21/2016 07:54AM
Last Post by o_lampe

Motor with Fast rpm at the start and Slow rpm at the end

by Tawn
352 4 04/18/2016 02:33PM
Last Post by bobc