Welcome! Log In Create A New Profile

Stepper Motors, Servo Motors, DC Motors

Discuss here what makes your printer moving.

Page 6 of 20 Pages:

4 567 8

Forum List New Topic RSS

	Views	Posts	Last Post
Stepper motors with 7.5deg steps? by heimerdinger	3,471	8	06/22/2016 09:20AM Last Post by kestux75
Can't get enough steps or maybe power by triggernom	372	4	06/08/2016 01:18PM Last Post by triggernom
interesting quirks with feedrate and new motor drivers. by mrsour	507	2	06/08/2016 10:39AM Last Post by mrsour
Identifing a damaged stepper by Gaou	390	1	06/02/2016 12:57PM Last Post by Gaou
how do i stop the motor shaft which has a load, from rotating when the power is shut off by za	431	7	05/30/2016 11:01AM Last Post by the_digital_dentist
Very jerky stepper movement by Jelby-John	4,380	20	05/27/2016 10:24PM Last Post by BioLumo
Resisting Voltage from Power Stage by sullivnc	304	3	05/25/2016 03:07PM Last Post by bobc
Voltage Rumba board by Hans123456789	566	1	05/19/2016 08:01AM Last Post by Hans123456789
Vibration at low speed by Nikel	2,126	6	05/18/2016 06:16PM Last Post by the_digital_dentist
Choice between two steppers by jonawald	394	1	05/12/2016 12:03AM Last Post by jonawald
C Driver not fully working by Nikel	266	2	05/06/2016 05:09AM Last Post by bobc
Help with Project List by jr9820	293	4	05/04/2016 11:17PM Last Post by cozmicray
DRV8825 "skipping" microsteps by peepsalot	7,700	8	05/04/2016 04:55PM Last Post by MrBaz
Stepper motor power supply by Harmsobuk	2,520	4	04/27/2016 09:56AM Last Post by the_digital_dentist
Stepper Motors from old Laser Printers by nike357	2,284	14	04/26/2016 02:24AM Last Post by nike357
Speed and torque calculation of stepper motor by bobdxcool	3,516	2	04/23/2016 06:11PM Last Post by dc42
Prusa i3 steppers by Stoica	343	3	04/21/2016 07:54AM Last Post by o_lampe
Motor with Fast rpm at the start and Slow rpm at the end by Tawn	405	4	04/18/2016 02:33PM Last Post by bobc
Motorcontrollers needing 5v, and RADDS 1.5 giving 3.3v by Exinferis	416	1	04/18/2016 12:57PM Last Post by Exinferis
Printer tremble by Gaou	278	4	04/18/2016 04:07AM Last Post by dc42
Cheapest place to get Nema 17 stepper motor? by 3DMachiner	1,134	3	04/18/2016 01:31AM Last Post by Gaou
RUMBA/A4988s w/24V result in motors working erratically by rtrahms	1,840	8	04/01/2016 03:54AM Last Post by dc42
Help Finding Drive/Controller by sullivnc	323	7	03/30/2016 09:29AM Last Post by dc42
Did anyone used linear hall sensors on BLDCs for position sensing? by misan	3,603	25	03/30/2016 03:47AM Last Post by misan
Needing Help With Egg Turner Project by swtrpeter	373	2	03/26/2016 03:44AM Last Post by Dust
Helpppp by jam	265	3	03/23/2016 12:37PM Last Post by jam
Ramps 1.4 x-axis broken by canteen234	426	1	03/22/2016 08:36PM Last Post by canteen234
Can I cover the back of the stepper motor by ihaveworms	325	2	03/22/2016 12:46PM Last Post by stephenrc
Stepper or brushed DC motor with sharp and fast turn by viktor80	415	2	03/17/2016 04:18PM Last Post by dc42
extruder acceleration/deceleration during printing by friarfish	632	3	03/12/2016 05:52AM Last Post by friarfish

Page 6 of 20 Pages:

4 567 8