Welcome! Log In Create A New Profile

Stepper Motors, Servo Motors, DC Motors

Discuss here what makes your printer moving.

Page 7 of 22 Pages:

5 678 9

Forum List New Topic RSS

	Views	Posts	Last Post
Use E1 driver on Rambo for independent Z levelling? by aegidius	785	2	08/07/2016 03:04AM Last Post by o_lampe
Stepper motors increase speed when touched. by snorrus	893	2	07/28/2016 01:39PM Last Post by o_lampe
Motors only turning one way by Aschie4589	2,075	9	07/26/2016 12:00PM Last Post by Aschie4589
Need help with servo end stop on Rambo 1.3 by ronnien55	1,017	2	07/24/2016 08:56AM Last Post by ronnien55
Help with calculating the speed required for motors by kelly27	733	2	07/13/2016 10:03PM Last Post by Dust
Nokia 5110 LCD for ramps by Danny141	1,287	1	07/10/2016 12:35PM Last Post by Danny141
[Solved] Z low torque with TMC2100 driver during Going-home by Arteriel	1,982	3	07/08/2016 04:40AM Last Post by dc42
Issues with Stepper by Ma_tits	941	8	07/05/2016 01:02PM Last Post by the_digital_dentist
Whats needed to run nema 23's? by The Borg	6,018	2	07/03/2016 10:02PM Last Post by the_digital_dentist
Issue with motor or Firmware by samotras	874	2	06/22/2016 02:00PM Last Post by o_lampe
Stepper motors with 7.5deg steps? by heimerdinger	5,747	8	06/22/2016 09:20AM Last Post by kestux75
Can't get enough steps or maybe power by triggernom	1,060	4	06/08/2016 01:18PM Last Post by triggernom
interesting quirks with feedrate and new motor drivers. by mrsour	967	2	06/08/2016 10:39AM Last Post by mrsour
Identifing a damaged stepper by Gaou	883	1	06/02/2016 12:57PM Last Post by Gaou
how do i stop the motor shaft which has a load, from rotating when the power is shut off by za	952	7	05/30/2016 11:01AM Last Post by the_digital_dentist
Very jerky stepper movement by Jelby-John	7,163	20	05/27/2016 10:24PM Last Post by BioLumo
Resisting Voltage from Power Stage by sullivnc	745	3	05/25/2016 03:07PM Last Post by bobc
Voltage Rumba board by Hans123456789	1,023	1	05/19/2016 08:01AM Last Post by Hans123456789
Vibration at low speed by Nikel	5,645	6	05/18/2016 06:16PM Last Post by the_digital_dentist
Choice between two steppers by jonawald	850	1	05/12/2016 12:03AM Last Post by jonawald
C Driver not fully working by Nikel	685	2	05/06/2016 05:09AM Last Post by bobc
Help with Project List by jr9820	721	4	05/04/2016 11:17PM Last Post by cozmicray
DRV8825 "skipping" microsteps by peepsalot	10,524	8	05/04/2016 04:55PM Last Post by MrBaz
Stepper motor power supply by Harmsobuk	4,201	4	04/27/2016 09:56AM Last Post by the_digital_dentist
Stepper Motors from old Laser Printers by nike357	4,587	14	04/26/2016 02:24AM Last Post by nike357
Speed and torque calculation of stepper motor by bobdxcool	5,769	2	04/23/2016 06:11PM Last Post by dc42
Prusa i3 steppers by Stoica	767	3	04/21/2016 07:54AM Last Post by o_lampe
Motor with Fast rpm at the start and Slow rpm at the end by Tawn	855	4	04/18/2016 02:33PM Last Post by bobc
Motorcontrollers needing 5v, and RADDS 1.5 giving 3.3v by Exinferis	879	1	04/18/2016 12:57PM Last Post by Exinferis
Printer tremble by Gaou	691	4	04/18/2016 04:07AM Last Post by dc42

Page 7 of 22 Pages:

5 678 9