Welcome! Log In Create A New Profile

Advanced

Developers

If you're reading this, you're a developer. Please join: http://reprap.org/mailman/listinfo/reprap-dev 
Subject Views Posts Last Post

Extruder run differently with same configuration Attachments

by cthsieh
2,098 3 07/14/2017 01:05AM
Last Post by scottybfg

Autocalibration: Measure distance to home from unknown position

by lhartmann
2,124 7 07/12/2017 05:06AM
Last Post by dc42

Aluminum Sheet Between Heater and Glass   (Pages: 1 2 3)

by Shachar85
7,712 79 07/07/2017 05:35AM
Last Post by dc42

CoreXZ Attachments   (Pages: 1 ... 4 5 6)

by nicholas.seward
30,035 170 07/05/2017 03:24PM
Last Post by Kenzu

Launching a new build plate Attachments

by andornot
1,963 1 07/03/2017 03:32PM
Last Post by andornot

Duet pressure advance

by deckingman
1,873 3 06/27/2017 04:08PM
Last Post by deckingman

New Delta printer calibration method with ray of light

by boylucky
1,911 4 06/23/2017 10:52AM
Last Post by dc42

Investigation into potential print speeds with a Diamond hot end

by deckingman
1,915 1 06/22/2017 01:09PM
Last Post by deckingman

Need help scroll display long file name on LCD Attachments

by jhlee98y
1,951 12 06/11/2017 08:49AM
Last Post by chris33

Where can I find info about the details of printer design

by Robin2
2,046 5 06/09/2017 09:37AM
Last Post by Ed would

Pololu/stepstick compatible stepper drivers without potmeter

by o_lampe
2,135 14 06/04/2017 10:05AM
Last Post by JustAnotherOne

6 in 1 out Hot-End development Attachments   (Pages: 1 2)

by sniper567
4,300 37 06/03/2017 03:43AM
Last Post by deckingman

Slic3r on mint 17 Qiana

by v1talogy
1,935 2 05/26/2017 12:05PM
Last Post by v1talogy

Trying to Understand GCode

by Nimo
1,827 6 05/21/2017 11:19AM
Last Post by Jb Sebastian

How to? GPL License for 3D printers

by Gonzalo.agrimbau
1,815 4 05/19/2017 03:23PM
Last Post by MattMoses

Can FPGA implement G-code?

by pkl520
2,939 3 05/07/2017 02:16PM
Last Post by rsc

SCARA Firmware

by MagnusNM
2,134 2 04/27/2017 01:21PM
Last Post by cozmicray

New 3D printer design for discussion - let's call it In-line design

by boylucky
3,096 18 04/19/2017 04:12PM
Last Post by boylucky

Controlling feed rates

by Nickolai
7,326 15 04/12/2017 10:51AM
Last Post by samiam

Controlling a RepRap with ESP8266 and no Arduino   (Pages: 1 2 3)

by lhartmann
12,667 86 04/10/2017 09:56AM
Last Post by Keemanaan

Is there someone to code something for me , thks smiling smiley

by studiodyne
2,609 8 04/08/2017 03:33PM
Last Post by VonRansak

reprap.org no SSL?

by cdaringe
2,374 2 04/08/2017 03:23PM
Last Post by VonRansak

M600 like custom change filament solution question

by DesignSmurf
2,388 8 04/07/2017 03:26AM
Last Post by DesignSmurf

Arcus3D M2 - Six material, active mixing linear delta 3d printer. Attachments   (Pages: 1 2)

by darenschwenke
5,323 33 04/05/2017 09:14PM
Last Post by kentmcn

Project of a universal SD card GCode sender

by toxnico
2,805 13 04/04/2017 05:22PM
Last Post by the_digital_dentist

DuetWiFi Lash-Up

by Giark
2,556 11 04/04/2017 01:59PM
Last Post by dc42

Multi colour printing without wipe or prime towers   (Pages: 1 2)

by deckingman
4,830 52 04/01/2017 02:53AM
Last Post by papakel

Delta 3D printer firmware for ULN2003 driver and 28BYJ-48 stepper motor

by boylucky
4,716 19 03/26/2017 07:54AM
Last Post by tgit23

In progress - hotend Attachments   (Pages: 1 2)

by JamesK
3,907 34 03/21/2017 09:28PM
Last Post by JamesK

C++ editor

by doodady
2,526 7 03/19/2017 05:14AM
Last Post by slippyr4