Subject		Views	Posts	Last Post
	Seeking help / advice by Micromental	1,766	3	02/25/2020 07:42PM Last Post by Roberts_Clif
	ESP32 pinout - MISO on input pins working? by newbob	5,180	1	02/24/2020 06:12PM Last Post by newbob
	Heated bed or Chamber PWM - set as inverted , but pins are high on reset (0C). How to set condition for PWM to be pulled Low after reset (0C) ? by lukaari	2,482	4	01/30/2020 05:35AM Last Post by Dancer
	ReprapMJ 3D Printed “Prusa Style” Nylon Capable and Easy to Use 3D Printer with Full 200mm Build Size but Small Footprint. The Basic Printer Has a Hardware/Vitamin Count of One Part (the build plate). by mikejeffs	2,674	6	01/25/2020 08:48AM Last Post by MechaBits
	Chamber PID temperature control by lukaari	1,800	5	01/21/2020 04:23PM Last Post by lukaari
	Adding Some Code on Marlin Firmware by hehenryprbo	2,826	10	01/21/2020 04:07PM Last Post by lukaari
	Start G-Code Script for toolchange by IG88	2,879	2	01/15/2020 11:21AM Last Post by dc42
	publish a page in RepRap by Reiszel	1,771	7	12/24/2019 02:34PM Last Post by Reiszel
	TMC2130 drivers no bi-directional motion by rrcaveman	1,896	3	12/23/2019 09:24PM Last Post by Dust
	Simple linear rail cube 3D printer with Duet 2 Wifi by perklus	1,847	3	12/13/2019 02:18PM Last Post by perklus
	St's L6470 stepper motor drivers by erhancm	1,957	1	11/22/2019 02:53AM Last Post by erhancm
	Documenting a printer design on reprap.org by MortarArt	1,741	4	11/09/2019 02:55AM Last Post by dc42
	Thermistor for 275 Celsius by uticatechclub	2,022	8	11/07/2019 10:11AM Last Post by uticatechclub
	printrbotSimpleMetalProimagesAndDocumentsUpload by jamesdanielv	1,902	3	11/06/2019 01:37PM Last Post by jamesdanielv
	Running broken Melzi board + stepper AND LCD 2004 by IamTheVector	2,203	6	10/28/2019 06:26PM Last Post by Dust
	atmega 2560 is Heating by Re523	3,208	4	10/03/2019 01:24AM Last Post by Dust
	Controlling a Printer With a Soundcard (I2S) on a Raspberry or orange Pi by lhartmann	6,814	10	09/30/2019 03:46PM Last Post by bschwand
	BL Touch on ANyCubic Kossel Linear Plus by norep	2,942	2	09/25/2019 02:07PM Last Post by norep
	How to program/reuse broken boards? by IamTheVector	1,868	10	09/16/2019 02:16PM Last Post by MKSA
	Emergency Stop function and terminology discussion by InsanityAutomation	1,649	5	09/14/2019 10:03AM Last Post by InsanityAutomation
	Plethora of 3D printing software open sourced! by Gerharddc	1,767	2	09/10/2019 07:02AM Last Post by VDX
	Driving a Warthog w120 with reprap by Giantkiller	2,284	8	08/29/2019 05:25PM Last Post by Giantkiller
	BFB 3000 bootloader issue by saif	1,713	1	08/13/2019 02:41PM Last Post by saif
	220V extruder ? by CJ.BRAVO	1,703	4	07/28/2019 11:12AM Last Post by Ohmarinus
	FFModule -- Adding Sounds & RGB Led to your Printer by VincentM	5,775	27	07/25/2019 12:19PM Last Post by tru_visual
	What do you think about this spindle? by evgeniy.romensky	1,779	2	06/17/2019 09:32AM Last Post by imqqmi
	TeensyPrinter: a RAMPS-like board built around the Teensy 3.6 by salfter	4,154	12	06/12/2019 02:19PM Last Post by bilsef1
	inkjet printer by Dshah	2,582	7	05/28/2019 03:37AM Last Post by VDX
	Printer board simulator/emulator? Marlin testing by Oldass	6,418	6	05/25/2019 08:55AM Last Post by Pippy
	Tweaking Marlin to run a Convoyer XY printer from an SD card by xdarko	1,778	2	05/19/2019 01:14AM Last Post by bryanandaimee