Welcome! Log In Create A New Profile

RAMPS Electronics

Support for the quite nice RAMPS Electronics. See also http://reprap.org/wiki/RAMPS.

Page 6 of 72 Pages:

4 567 8

Forum List New Topic RSS

	Views	Posts	Last Post
Use SERVOS connector for heatbed SSR? by tobo	887	2	10/03/2019 03:43PM Last Post by tobo
Mini12864 Panel - FYSETC / ramps 1.4 by Ton_Crazy	1,432	2	09/22/2019 07:34AM Last Post by Dust
Motors problem by 3bdelli	973	3	09/21/2019 09:50AM Last Post by 3bdelli
Discount smart controller lcd No Sd Card by dfox1787	4,627	10	09/18/2019 04:09PM Last Post by AndyD
Using Aux1 by TechMage	902	1	09/07/2019 12:19AM Last Post by TechMage
problems with my setup by Con-1025	990	5	09/05/2019 08:47PM Last Post by Dust
Heat Bed not heating by adrian_rg	4,808	12	08/07/2019 12:01PM Last Post by adrian_rg
Connect Mosfet to other pins by BeSpace	1,081	3	07/28/2019 10:11AM Last Post by BeSpace
Help in wiring SD card reader to RAMPS 1.4 by disneytoy	17,993	10	07/03/2019 06:17AM Last Post by Ohmarinus
Heatbed does not heat up by Ravalen	1,138	1	07/01/2019 06:56PM Last Post by Ravalen
Best Ramps Board? by Mendelevium99	2,877	4	06/25/2019 03:10AM Last Post by motymen
Z axis dont stop while printing by neillcl	1,125	5	06/20/2019 12:36AM Last Post by Dust
LCD only works with USB connected by regpye	17,350	17	06/18/2019 03:36AM Last Post by dc42
L298N Ramps1.4 by 3DLTech	1,431	7	06/01/2019 12:34PM Last Post by VDX
DRV8825 and TL Smoother board? by Ohmarinus	1,308	1	05/26/2019 05:25AM Last Post by Ohmarinus
Replace Ramps LCD by button by Rickalac	873	3	05/20/2019 11:54AM Last Post by Rickalac
24v board upgrade by Rodney	918	1	05/13/2019 05:25PM Last Post by Rodney
Adding bluetooth (HC05) to Ramps 1.4 headache by Ohmarinus	2,811	11	05/11/2019 02:31PM Last Post by Ohmarinus
Stepper Stops Extruding (Video) by liminal1	855	5	05/11/2019 12:09AM Last Post by liminal1
Balance potentiometer for stepper drivers by liminal1	928	10	05/11/2019 12:02AM Last Post by liminal1
RAMPS 1.5 - Z-Axis won't go down by JoeK1973	962	4	05/07/2019 09:13AM Last Post by Ohmarinus
Ramps 1.4 LCD showing 2 white "block" lines by Kubas_inko	2,469	8	05/04/2019 09:29AM Last Post by Dust
Controlling stepper motors with LabVIEW+RAMPS 1.4 by lacorca	1,824	2	04/30/2019 07:07AM Last Post by Dust
RAMPS 1.5 PS_ON, RAMPS 1.6 PS_ON moved by papergeek	1,773	1	04/30/2019 06:10AM Last Post by papergeek
Heatbed temperature keeps increasing. by FCStevens	783	3	04/26/2019 02:14PM Last Post by MMcLure
Ramps 1.4 no power on 12V by MikeCL	772	1	04/22/2019 10:38PM Last Post by MikeCL
Wiring ESP8622 + Touch panel Jz-TS35 to RAMPS 1.4 by cabped	957	3	04/14/2019 11:46AM Last Post by cabped
MPX.3 - stepper drivers dead? by Br003	1,703	4	04/08/2019 10:41PM Last Post by Roberts_Clif
EXTERNAL SD CARD PINS schematic by holala02	724	2	04/06/2019 09:40AM Last Post by Dust
Is possible to add external i2c eeprom to arduino for use by ramps by bobble991	644	1	04/06/2019 05:51AM Last Post by bobble991

Page 6 of 72 Pages:

4 567 8