Welcome! Log In Create A New Profile

Advanced

RAMPS Electronics

Support for the quite nice RAMPS Electronics. See also http://reprap.org/wiki/RAMPS
Subject Views Posts Last Post

What do you use for Z steps?

by Axim2012
781 3 01/25/2012 04:11AM
Last Post by nophead

Recommended way to connect RAMPS to PC PSU?

by Pointedstick
950 2 01/18/2012 08:56PM
Last Post by Andrew Smith

[SOLVED] RAMPS 1.4 Stops heating

by mostley
985 5 01/16/2012 03:51PM
Last Post by mostley

Hint soldering RAMPS 1.2 Attachments

by scuba
747 2 01/13/2012 09:44PM
Last Post by dissidence

[SOLVED] Printing FAILS!

by pikelo
630 2 01/11/2012 03:50PM
Last Post by pikelo

[solved] RAMPS 1.4 Heater Issues

by d4rwen
1,310 3 01/07/2012 11:48PM
Last Post by d4rwen

Question about RAMPS wiring

by nigel_mck
851 3 01/07/2012 10:47PM
Last Post by nigel_mck

Arduino getting really hot, and the Ramps turn off

by MatheusBrum
1,036 2 01/05/2012 12:56AM
Last Post by dissidence

Can't Upload Firmware to RAMPS

by vulcanrd
3,440 7 01/03/2012 05:13AM
Last Post by BrazenArtifice

[Solved] heater pinouts not working

by 3D2B
719 1 01/02/2012 09:12AM
Last Post by 3D2B

[Resolved] Ramps 1.4 Not driving steppers

by nubspera
1,162 5 01/01/2012 09:23PM
Last Post by nubspera

prints reseting

by Gulf
832 12 12/31/2011 07:31AM
Last Post by misan

I am having a problem with the Stepper extruder

by paulharrington
579 5 12/25/2011 05:51PM
Last Post by johnnyr

US Parts List for RAMPS Attachments

by Chris Martin
2,836 9 12/23/2011 12:59AM
Last Post by Infallibel

PCB MK1 + power supply not enough power? Attachments

by pikelo
967 6 12/22/2011 03:24AM
Last Post by pikelo

Amp Rating

by thewaterengine
1,466 7 12/21/2011 10:22AM
Last Post by rcs

RAMPS 1.2 no power

by cr3a7ure
790 6 12/18/2011 11:31AM
Last Post by cr3a7ure

[SOLVED] Pololu pulsing issue

by unicoder
2,333 9 12/16/2011 05:06AM
Last Post by evilb

13.3V with RAMPS 1.4 with 1N4004 diode

by mostley
1,036 3 12/15/2011 07:05AM
Last Post by mostley

RAMPS Z only one direction, extruder doesn't heat

by pgnat
868 2 12/13/2011 05:15PM
Last Post by misan

Newbie trying to get Prusa with RAMPS 1.4 working

by miro87043
1,521 11 12/13/2011 04:48AM
Last Post by nophead

Problem with endstops.

by Rico
514 2 12/12/2011 05:21AM
Last Post by pikelo

ramps connects, motors don't move

by ambiguousphoton
731 8 12/11/2011 11:57PM
Last Post by BrazenArtifice

SD-Ramps not working

by kkberg
1,431 6 12/08/2011 03:20PM
Last Post by DrE

OptoEndstop 2.1

by windcatcher
1,495 14 12/05/2011 12:11PM
Last Post by De Uzzi

RAMPS 1.4/Mega 2560 Pololu drivers ok but X,Y,Z rotate only in one direction

by pic1832
1,327 5 12/05/2011 06:49AM
Last Post by pic1832

ramps+32bit arduino will it fid.

by michel pet
1,005 3 11/26/2011 12:44PM
Last Post by michel pet

Help connecting arduino mega 1280 to ramps & computer

by T-Carbs
1,825 3 11/25/2011 07:25PM
Last Post by T-Carbs

RAMPS single board

by chrissketch
843 8 11/24/2011 12:46PM
Last Post by royco

Connecting Problem (fixed)

by BobFA
603 1 11/19/2011 09:02PM
Last Post by BobFA