Welcome! Log In Create A New Profile

RAMPS Electronics

Support for the quite nice RAMPS Electronics. See also http://reprap.org/wiki/RAMPS.

Page 62 of 72 Pages:

60 616263 64

Forum List New Topic RSS

	Views	Posts	Last Post
Can someone post their work prusa/ramps1.4/marlin config file? by StuSeitz	689	2	01/21/2013 02:22AM Last Post by xclusive585
Electronic disturbance (ground loop)? by zungmann	702	4	01/10/2013 09:07AM Last Post by zungmann
Fan issue? by Berra	618	5	01/09/2013 03:18AM Last Post by Berra
Can moving steppers damage the RAMPS board/drivers? by Qsilver	1,278	4	01/05/2013 03:09PM Last Post by Gulf
changing arduino analog pin for temp sensor by Fbmfbm	2,912	3	01/02/2013 08:43AM Last Post by Fbmfbm
Cannot connect to RAMPS to upload new firmware or with Pronterface by prcdslnc13	3,278	10	01/01/2013 03:28PM Last Post by picapau
Whats the FR 100 on reprapdiscount lcd? by skew	11,504	3	01/01/2013 02:46PM Last Post by skew
Arduino mega vs Uno vs Duemilanove by Hobbes20xx	8,060	7	12/30/2012 10:09PM Last Post by ElectronicMAN
Prusa/RAMPS 1.4 worked for months, no longer good prints by spacey123	1,432	8	12/28/2012 06:44PM Last Post by spacey123
Noob question....LCD Ramps 1.4 by Judofish	1,401	4	12/20/2012 03:44PM Last Post by jbernardis
Reversed direction on steppers by Gyvven	632	2	12/19/2012 12:49AM Last Post by Cefiar
Printer works but wont start a print. by StuSeitz	659	4	12/15/2012 01:51AM Last Post by Polygonhell
Problem with reading temperatures by Bozzibo	816	5	12/06/2012 12:34PM Last Post by G
RAMPS for RepStrap by Dogstar	720	7	12/06/2012 12:26PM Last Post by Dogstar
What's an Amp between friends? by Qsilver	703	2	12/05/2012 07:26PM Last Post by Cefiar
RAMPS 1.4 Mosfet issue by maca_404	15,199	7	12/05/2012 12:43PM Last Post by nophead
RAMPS 1.4 and Mega 2650 Arduino Pin numbers by murf83	36,013	4	11/29/2012 03:44PM Last Post by jbernardis
Powering a RAMPS set up from a 19V supply by Alzibiff	1,893	3	11/27/2012 12:44PM Last Post by Alzibiff
Help Upgrading to Marlin on Ultimachine RAMPS v1.4 for Prusa Mendel by finks	1,297	4	11/26/2012 07:21AM Last Post by finks
Optional 5v power input (edited) by foshon	775	1	11/23/2012 03:40PM Last Post by foshon
using the unused arduino pins by jbernardis	1,452	6	11/17/2012 12:58AM Last Post by redreprap
CAD - 3D Model File of RAMPS board by RapidFab	6,416	8	11/12/2012 10:36AM Last Post by archistrong
shorted stepper driver by finger? by everoptimistic	3,434	23	11/11/2012 03:17PM Last Post by redreprap
Wanted by rhys1443	566	2	11/11/2012 09:22AM Last Post by Traumflug
Test 1 motor on RAMPS 1.4 by murf83	1,225	2	11/09/2012 05:20PM Last Post by redreprap
Power supply goes off mid print by Karlberg	958	3	11/03/2012 03:39PM Last Post by Karlberg
Somebody help with a copy CONFIGURATION.H / ADV.H and PINS.H by nonaak	1,732	5	11/03/2012 02:55PM Last Post by nonaak
[Fixed]Stepper driver just died. Was it a fluke, or should I be worried? by Locus	824	2	10/30/2012 02:07AM Last Post by Locus
powering or connection issues!!!! by prairiewolf407	635	5	10/23/2012 03:25AM Last Post by prairiewolf407
Different input voltage on RAMPS 1.4 by LHelge	2,509	5	10/21/2012 06:45PM Last Post by Cefiar

Page 62 of 72 Pages:

60 616263 64