Welcome! Log In Create A New Profile

Advanced

Printing

Printing issues ... 
Subject Views Posts Last Post

Problem Reloading Filament During Print

by aboforever
682 3 11/30/2012 11:58PM
Last Post by zelogik

After printing sometimes it stay in last point do not go home

by IMGeorge
560 1 11/30/2012 04:13AM
Last Post by IMGeorge

Typical print quality issues... Attachments

by aucbcam
958 5 11/28/2012 04:10PM
Last Post by juergen99

Z axis lifts up on start of print

by RepRapMza
764 5 11/28/2012 02:59PM
Last Post by Sniper4395

too much horizontal space, unjoined layering issue in vertical walls

by biketool
911 10 11/25/2012 12:46PM
Last Post by Dirty Steve

What causes this surface finish?

by IanJohnson
1,161 3 11/21/2012 05:44PM
Last Post by Dirty Steve

How to improve print quality Attachments

by Myles
1,446 10 11/19/2012 07:40PM
Last Post by Dirty Steve

Dimensions off on diagonals

by IanJohnson
521 5 11/19/2012 03:27PM
Last Post by IanJohnson

Excess material at corners Attachments

by GreyMark7650
3,523 11 11/18/2012 04:29PM
Last Post by richgain

No extruding when printing

by Myles
507 5 11/14/2012 06:49PM
Last Post by Myles

Solution to curling overhangs? Attachments

by stoof
2,312 5 11/14/2012 08:54AM
Last Post by unlucky1

Bunch of problems with PLA   (Pages: 1 2)

by eniq1on
2,468 35 11/07/2012 03:19AM
Last Post by ben11c

Dimension support material

by jimdaug
569 1 10/30/2012 01:35AM
Last Post by jimdaug

Setting Up New Printer Dimensions?

by sypher
615 5 10/26/2012 06:42PM
Last Post by sypher

Can Bridging Make This Part? Attachments

by DGC PartWorks
736 11 10/26/2012 04:09PM
Last Post by Evogenius

Print quality varies with direction

by Dardaq
603 3 10/24/2012 05:28PM
Last Post by Sniper4395

Layers don't stick together Attachments

by ohin
4,423 8 10/24/2012 03:14PM
Last Post by Sniper4395

Reducing Stringing Between Objects

by Sniper4395
1,481 3 10/20/2012 02:44PM
Last Post by Dirty Steve

Layers are poorly formed/sparse Attachments

by iggyfigs
819 4 10/18/2012 03:17PM
Last Post by iggyfigs

ReplicatorG header cap?

by sypher
474 2 10/17/2012 09:17PM
Last Post by sypher

Marlin not getting hot enough

by wookieegunner
1,424 7 10/15/2012 11:03PM
Last Post by vwtimah

Printer slows down around tight bends, with blobbing as a result...

by Speedsoda
863 9 10/11/2012 01:46PM
Last Post by Wraithnot

PVA Printing Idea

by t357
862 6 10/10/2012 06:28PM
Last Post by Sniper4395

PLA printing issue confused smiley

by epiteszsrac21
761 5 10/08/2012 07:51AM
Last Post by epiteszsrac21

Nozzle tip width and little sheres on print Attachments

by Dirty Steve
832 2 10/06/2012 11:39AM
Last Post by Dirty Steve

How to increase control over extrudate flow?

by Speedsoda
607 2 10/05/2012 08:57PM
Last Post by EMH Studios

Tips for increasing print quality Attachments

by liam
1,238 2 10/05/2012 09:06AM
Last Post by Dale Dunn

Gcodes for a filament change mid-print

by Flackster
6,379 9 10/04/2012 08:39AM
Last Post by Sniper4395

Printing quality suggestions? Attachments

by JazzyMT
2,179 4 10/04/2012 02:20AM
Last Post by Anonymous User

Print Size Limitations Attachments

by BenitoSanduchi
1,582 5 10/04/2012 02:20AM
Last Post by Anonymous User