Subject		Views	Posts	Last Post
	Leaky Extruder by jevanboone	1,502	4	12/06/2013 09:20AM Last Post by jevanboone
	What is the key to printing really small items? by vetteguy112233	1,161	6	12/04/2013 10:24PM Last Post by Dirty Steve
	Hotend and Heated Bed Temps dropping while printing by Hawkeye0914	1,133	7	12/03/2013 12:28AM Last Post by GowthamJGR
	3Dstuffmaker Prusa Explorer firmware by Hubologista	1,037	3	12/02/2013 06:17PM Last Post by Hubologista
	Error on my printout by Sajmon	586	6	12/01/2013 01:01AM Last Post by waitaki
	Waviness/Ripples in surface parallel to Y by leshric	1,381	8	11/30/2013 01:44PM Last Post by Dirty Steve
	Passive Stepper Motor Cooling by sd3dprinting	1,031	1	11/27/2013 01:04PM Last Post by sd3dprinting
	Infilled areas by markmotor	533	3	11/27/2013 10:42AM Last Post by markmotor
	Drying filament other than oven by fishhf	1,770	4	11/26/2013 07:46PM Last Post by papergeek
	Slave instead of Master Melzi ? by [email protected]	769	1	11/26/2013 09:41AM Last Post by [email protected]
	First machine and first print problems. by MeMadMax	700	3	11/23/2013 03:53AM Last Post by MeMadMax
	Inconsistent nozzle flow...is it filament or extruder/hot end issue? by mycarlooksfast	14,721	8	11/22/2013 09:08AM Last Post by mycarlooksfast
	Prints with height don't adhere to base by Sekritz	751	5	11/21/2013 12:58AM Last Post by Sekritz
	Layer gaps by sungod3k	911	5	11/19/2013 12:57PM Last Post by sungod3k
	Width and filling troubles by Yshuro	773	3	11/19/2013 12:51PM Last Post by jcabrer
	Prints with ABS have a corner curling, same corner every time by Phizinza	3,562	9	11/19/2013 12:45PM Last Post by papergeek
	Boulges in 90 degree junctions by Recoil	610	2	11/19/2013 12:41PM Last Post by jcabrer
	Problems with Overhang & Loosening layers by spekkie2002	1,079	3	11/19/2013 03:58AM Last Post by spekkie2002
	Why do I keep getting this happen... by gppk	577	3	11/18/2013 07:43PM Last Post by jcabrer
	First print problems by strat	544	4	11/18/2013 07:27PM Last Post by jcabrer
	"fibrous, and half sticks" by jbourdon	412	2	11/16/2013 04:35PM Last Post by Sublime
	When using less than 100% infill it is too thin and misses bits by Phizinza	820	2	11/15/2013 12:18AM Last Post by Sublime
	Print surface quality issue. [SOLVED] by tookys	3,208	5	11/13/2013 01:59PM Last Post by flyboy
	Top Layer by Tec Print	879	3	11/05/2013 08:37PM Last Post by waitaki
	Extruder Slippage, HELP?!? by phate	7,249	9	11/03/2013 03:06PM Last Post by ShawnT98027
	First print , having some trouble by SpreadTheGood	538	3	11/02/2013 06:46PM Last Post by tmorris9
	Print bed adhesion methods... Vinyl keeps coming up! by Phizinza	1,346	3	11/02/2013 04:38PM Last Post by phord
	z-axis calibration by Mickman	893	3	10/31/2013 04:12AM Last Post by rhmorrison
	Newbie - need help with surface quality issues by flyboy	1,148	4	10/30/2013 04:23PM Last Post by Sublime
	Tried printing on fiberglass laminate? by 3DPrinterNinja	1,570	6	10/28/2013 09:51PM Last Post by 3DPrinterNinja