Welcome! Log In Create A New Profile

Advanced

Printing

Printing issues ... 
Subject Views Posts Last Post

Smallest nozzle ever?

by sungod3k
1,047 10 01/17/2013 05:37AM
Last Post by nophead

Prints leaning to side Attachments

by Matouš
983 3 01/17/2013 05:22AM
Last Post by Matouš

printing quality at small parts Attachments

by Irgendwer_Aus_Irgendwo
1,065 8 01/16/2013 09:23AM
Last Post by Irgendwer_Aus_Irgendwo

Layer alignment issue Attachments

by kri
665 4 01/13/2013 12:23AM
Last Post by tsb4k

Last layer incomplete

by Megdor
807 5 01/12/2013 02:52PM
Last Post by swhitlock

circular top layer issue.

by fixedtrd
539 2 01/10/2013 10:44AM
Last Post by Chipper

prints go bad after a cm high or so? Attachments

by rrr7
1,749 4 01/10/2013 08:16AM
Last Post by rrr7

printing issues Attachments

by printman
723 2 01/09/2013 08:11PM
Last Post by printman

Circles not smoothe, but jagged?

by mortinus
677 3 01/09/2013 07:52AM
Last Post by mortinus

PLA keep on curling up on exit on extruder head

by sypher
18,079 20 01/08/2013 06:02PM
Last Post by Airtripper

Thin wall test turns to tangled mess Attachments

by devonv
1,370 7 01/08/2013 05:08PM
Last Post by JazzyB

Alternatives to acetone

by ScottishMario
2,815 7 01/08/2013 02:07PM
Last Post by pokey9000

Layer thickness..... How does it work?

by Replace
827 7 01/08/2013 12:21PM
Last Post by Polygonhell

reprappro huxley pronterface - no HOME ALL or IDLE button??

by paddy10tellys
1,106 3 01/08/2013 11:51AM
Last Post by herisuprapto

Getting a PRECISION print - what parameters affect it?

by rtrahms
1,027 6 01/08/2013 09:16AM
Last Post by rtrahms

How to tell if this material is ABS or PLA? (or other?)

by JazzyB
7,349 30 01/08/2013 03:35AM
Last Post by JazzyB

Less detail in Y direction and open lattice pattern on top Attachments

by devonv
776 6 01/06/2013 07:30PM
Last Post by rrr7

GCode Issue? Attachments

by sulley
592 2 01/03/2013 02:17AM
Last Post by sulley

Polish a printed PLA Part

by SteveMac
4,014 8 01/01/2013 06:41PM
Last Post by Weedz

Printing a light tube or guide in clear PLA?

by marcosscriven
996 5 01/01/2013 07:03AM
Last Post by james glanville

Dimension issues

by JazzyB
1,233 21 12/30/2012 07:39AM
Last Post by JazzyB

Stringy filament - a temperature thing?

by Alzibiff
6,104 4 12/29/2012 05:17AM
Last Post by Sublime

blobs and top layer probs Attachments

by stu121
1,376 6 12/28/2012 11:28PM
Last Post by mortinus

What causes flat botton finishing?

by fsamir
931 17 12/28/2012 11:06PM
Last Post by mortinus

Gaps and separation in outer layers Attachments

by prcdslnc13
1,472 5 12/28/2012 08:36PM
Last Post by Beekeeper

J-head uneven flow

by Karlberg
1,335 9 12/27/2012 10:14AM
Last Post by Karlberg

Layer displacements issues Attachments

by pikelo
1,370 13 12/27/2012 07:29AM
Last Post by Greg Frost

Problems when i print overhangs Attachments

by CharlieSteurbaut
896 12 12/27/2012 05:42AM
Last Post by CharlieSteurbaut

Prusa printer locks up when Z goes taller than 45mm.

by librav
716 2 12/17/2012 09:23AM
Last Post by HansPeterHaastrup

Gap between infill and perimeter Attachments

by Ecir Hana
1,655 6 12/15/2012 07:35PM
Last Post by Dirty Steve