Welcome! Log In Create A New Profile

Advanced

Printing

Printing issues ... 
Subject Views Posts Last Post

Using dilute PVA glue to stop curlingconfused smiley

by MotoBarsteward
3,069 10 07/11/2012 02:40AM
Last Post by MotoBarsteward

Can excess filament cause curl? Attachments

by nb99
874 1 07/06/2012 09:23PM
Last Post by nb99

print area out of bounds

by paddy10tellys
1,321 5 07/05/2012 09:43PM
Last Post by dustynus

Hole, inside and outside dimensions wrong

by MotoBarsteward
2,840 11 07/04/2012 06:49PM
Last Post by MotoBarsteward

Weird curling with PLA on heated bed of glass Attachments

by Mazaw
7,440 20 07/03/2012 01:48PM
Last Post by idiot_secant

Nozzle touching the object after going up 5mm

by scanboy
1,017 5 07/03/2012 12:56AM
Last Post by aplavins

Stripes/Layers

by cunningham
877 3 07/03/2012 12:51AM
Last Post by aplavins

Single Wall cube test Attachments

by Etherflash
1,219 5 07/03/2012 12:45AM
Last Post by aplavins

Odd distortion in print in X axis direction

by MotoBarsteward
707 2 07/03/2012 12:42AM
Last Post by aplavins

Beginners guide to Pronterface settings?

by 3D2B
13,167 4 07/01/2012 06:18AM
Last Post by RegionX

first print - a bit naff Attachments

by paddy10tellys
760 4 06/30/2012 06:57AM
Last Post by Dad911

hot end

by bobbykey
688 4 06/27/2012 06:59AM
Last Post by Andrew Smith

too much plastic Attachments

by Etherflash
2,107 11 06/26/2012 04:09PM
Last Post by dustynus

New MendelMax 1.0 Just starting to print

by kaflick
1,327 14 06/19/2012 04:35AM
Last Post by AlexFielder1980

Extreme grip on heated bed with PVA: Video

by rantenki
1,810 1 06/17/2012 03:26PM
Last Post by rantenki

ABS comes loose of heatbed

by Replace
2,543 12 06/16/2012 05:43PM
Last Post by joedouce

Printer calibration inner holes

by Etherflash
1,755 4 06/15/2012 07:00AM
Last Post by nophead

Examples of Fan Locations on Prusa for PLA

by Enlightx
956 3 06/13/2012 09:48PM
Last Post by GITRDUN

PLA printing problems

by FreezeS
1,290 7 06/12/2012 10:10PM
Last Post by Anonymous User

Bottom few layers are too wide Attachments

by 3dcreationsllc
884 2 06/12/2012 01:56AM
Last Post by Euhedral

Gcode Commands

by Jusme
914 3 06/09/2012 09:27PM
Last Post by Jusme

Walls not fusing (abs)

by Barry_Scott
755 5 06/05/2012 11:14AM
Last Post by Barry_Scott

Calibration Problem Attachments

by tangz
762 3 06/04/2012 07:35PM
Last Post by aplavins

[Solved]Problems with shell layers not sitting on each other Attachments

by ne7rag3
888 6 06/02/2012 07:10PM
Last Post by ne7rag3

How to print a pin in a hole?

by jrsteensen
704 3 06/01/2012 07:06PM
Last Post by Mkouri

Holes in parimeter of print

by Barry_Scott
621 6 06/01/2012 04:35PM
Last Post by Barry_Scott

Configuration Print with Prusa - need help Attachments

by screamnAbdab
941 5 06/01/2012 04:07PM
Last Post by s4lt3d

Cubes too large and holes too small.

by sminnee
1,493 3 06/01/2012 03:36PM
Last Post by s4lt3d

Problem with specific prints

by HansPeterHaastrup
588 5 05/30/2012 03:47PM
Last Post by HansPeterHaastrup

Curling on Overhangs and Temperature Attachments

by gtg252b
1,087 7 05/23/2012 01:38PM
Last Post by gtg252b