Subject		Views	Posts	Last Post
	PLA keep on curling up on exit on extruder head by sypher	22,457	20	01/08/2013 06:02PM Last Post by Airtripper
	Thin wall test turns to tangled mess by devonv	1,575	7	01/08/2013 05:08PM Last Post by JazzyB
	Alternatives to acetone by ScottishMario	3,056	7	01/08/2013 02:07PM Last Post by pokey9000
	Layer thickness..... How does it work? by Replace	959	7	01/08/2013 12:21PM Last Post by Polygonhell
	reprappro huxley pronterface - no HOME ALL or IDLE button?? by paddy10tellys	1,201	3	01/08/2013 11:51AM Last Post by herisuprapto
	Getting a PRECISION print - what parameters affect it? by rtrahms	1,111	6	01/08/2013 09:16AM Last Post by rtrahms
	How to tell if this material is ABS or PLA? (or other?) by JazzyB	7,608	30	01/08/2013 03:35AM Last Post by JazzyB
	Less detail in Y direction and open lattice pattern on top by devonv	849	6	01/06/2013 07:30PM Last Post by rrr7
	GCode Issue? by sulley	703	2	01/03/2013 02:17AM Last Post by sulley
	Polish a printed PLA Part by SteveMac	4,162	8	01/01/2013 06:41PM Last Post by Weedz
	Printing a light tube or guide in clear PLA? by marcosscriven	1,287	5	01/01/2013 07:03AM Last Post by james glanville
	Dimension issues by JazzyB	1,328	21	12/30/2012 07:39AM Last Post by JazzyB
	Stringy filament - a temperature thing? by Alzibiff	7,125	4	12/29/2012 05:17AM Last Post by Sublime
	blobs and top layer probs by stu121	1,891	6	12/28/2012 11:28PM Last Post by mortinus
	What causes flat botton finishing? by fsamir	1,071	17	12/28/2012 11:06PM Last Post by mortinus
	Gaps and separation in outer layers by prcdslnc13	1,553	5	12/28/2012 08:36PM Last Post by Beekeeper
	J-head uneven flow by Karlberg	1,491	9	12/27/2012 10:14AM Last Post by Karlberg
	Layer displacements issues by pikelo	1,495	13	12/27/2012 07:29AM Last Post by Greg Frost
	Problems when i print overhangs by CharlieSteurbaut	977	12	12/27/2012 05:42AM Last Post by CharlieSteurbaut
	Prusa printer locks up when Z goes taller than 45mm. by librav	800	2	12/17/2012 09:23AM Last Post by HansPeterHaastrup
	Gap between infill and perimeter by Ecir Hana	1,774	6	12/15/2012 07:35PM Last Post by Dirty Steve
	random stall, SENDING:M105 will wait forever [SOLVED maybe] by dustynus	1,922	2	12/14/2012 12:36PM Last Post by ducati438
	Sagging, rough borders around holes, and some bobbling on corners by marcosscriven	1,103	4	12/14/2012 04:45AM Last Post by garyhodgson
	If your PLA isn't sticking... by marcosscriven	742	2	12/14/2012 04:16AM Last Post by DeuxVis
	Finishing solid layers by epiteszsrac21	728	2	12/13/2012 11:12PM Last Post by IanJohnson
	Printing issue! by epiteszsrac21	770	5	12/13/2012 05:19PM Last Post by epiteszsrac21
	occasional irregular segment by mfinn	1,222	7	12/12/2012 02:47PM Last Post by A
	Strange prusa printing issue by maca_404	885	8	12/10/2012 06:20PM Last Post by Dirty Steve
	The right side of my prints are always bad by z3ro	1,053	11	12/10/2012 02:09PM Last Post by Logrod
	Setting E-steps for different materials? by JazzyB	993	2	12/09/2012 04:44PM Last Post by Traumflug