Welcome! Log In Create A New Profile

Advanced

Printing

Printing issues ... 
Subject Views Posts Last Post

How do I find out the right PETG bridge settings? Attachments

by Aldebaran94
257 2 04/03/2020 09:16AM
Last Post by Roberts_Clif

Extruder stops temporarily during print

by joaoabs
405 5 03/28/2020 09:42AM
Last Post by the_digital_dentist

Z-Axis moving up on same layer

by nadaol
559 6 03/25/2020 08:39PM
Last Post by nadaol

Regular Pimples on the printing Surface Attachments

by koiti
356 3 03/25/2020 12:45PM
Last Post by Vidius

Variable Extruder flow rate depending on filament diameter.

by hari3d
190 2 03/25/2020 09:24AM
Last Post by Roberts_Clif

Mystery colour streaks - WILLING TO PAY FOR SOLUTION Attachments

by BluePeachBread
517 6 03/23/2020 10:34AM
Last Post by MCcarman

Autoleveling will randomly fail

by foul_owl
251 6 03/20/2020 07:04PM
Last Post by foul_owl

Hotend heating problems

by Mahir
263 6 03/19/2020 09:59AM
Last Post by Mahir

Print stalls with equal extrusion values

by benecito
266 4 03/12/2020 10:20AM
Last Post by benecito

EXTRUDER ACTING GOOFY

by BikerJim
296 3 03/04/2020 05:44AM
Last Post by BikerJim

E steps/mm correct, but inaccurate wall widths?

by KCheshire
470 11 03/02/2020 08:07AM
Last Post by MCcarman

SKR 1.3 3D-touch

by tomstr21
321 1 02/27/2020 03:43AM
Last Post by tomstr21

A8 E3Dv6 and silk PLA filament help

by dlc60
264 1 02/26/2020 06:17PM
Last Post by dlc60

Bltouch not leveling in one corner

by MrAwesomePhantom
334 1 02/25/2020 12:59AM
Last Post by MrAwesomePhantom

Nozzle to low after auto bed level grrrrrr

by bulldogbob
265 2 02/24/2020 12:18AM
Last Post by dlc60

M851 issue

by MikeCL
581 3 02/23/2020 12:12PM
Last Post by bulldogbob

Error in printer heating

by pvishalp19
567 9 02/22/2020 09:24AM
Last Post by Dust

Hotend temperature decreasing but firmware not see that

by furkanbcr
750 8 02/20/2020 06:11PM
Last Post by Raider

XYZ calibration cube X on cube looks bad

by npm1
307 1 02/17/2020 01:57PM
Last Post by npm1

Systematic approach for determining print settings

by 3DKrysh
516 3 02/17/2020 07:37AM
Last Post by 3DKrysh

Geometric patterns on sidewalls of prints Attachments

by alvinflumox
708 9 02/16/2020 03:42PM
Last Post by alvinflumox

Enervision D printer ET-K1 alarm issue

by roger69580
256 1 02/09/2020 08:25PM
Last Post by roger69580

Problem after an hour of printing Attachments

by panas78
435 12 02/09/2020 05:10AM
Last Post by panas78

conecting problems

by bolean
263 1 02/08/2020 10:09AM
Last Post by bolean

Printing issues.. at a loss

by jdebuhr
1,197 25 02/07/2020 08:56AM
Last Post by jdebuhr

Problem nema23 tb6600 Marlin

by furkannr
690 8 02/02/2020 09:42AM
Last Post by alessandro.maffei

heatbed not going past 80

by gerbo
293 2 01/31/2020 02:14PM
Last Post by the_digital_dentist

Spidery PETG and globbing Attachments

by dlc60
433 5 01/28/2020 03:58PM
Last Post by G3DBuilder

Pronterface Not Connecting

by Theorist
24,741 11 01/27/2020 10:34AM
Last Post by TerryD15

E1 Heating failed, printer Halted, please reset? Help Attachments

by fierypackman
1,829 8 01/27/2020 04:47AM
Last Post by fierypackman