Welcome! Log In Create A New Profile

Tantillus

http://www.reprap.org/wiki/Tantillus

Page 4 of 11 Pages:

1 2 345

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	Banding and failed/successful hacks to resolve it by willworkforplastic	4,131	21	02/13/2014 03:14AM Last Post by willworkforplastic
	Sourcing Tantillus Parts by LucasGelf	1,357	13	02/12/2014 09:45AM Last Post by flemming
	Expanding the Tantillus Printed Version by LucasGelf	872	4	02/11/2014 11:50AM Last Post by Sublime
	reprap.me J-head back pressure by blabberjack	1,377	9	02/11/2014 01:15AM Last Post by wingnut
	Expanding the lasercut case? by tschmid	584	3	02/08/2014 09:39PM Last Post by tschmid
	1.75mm extruder mod by LucasGelf	845	3	02/07/2014 09:03AM Last Post by LucasGelf
	1.75mm Extruder by LucasGelf	647	1	02/06/2014 10:02PM Last Post by LucasGelf
	Hobbed bolt by Nick101	705	4	02/04/2014 04:52PM Last Post by Sublime
	Motor Question by Chrisp	452	2	02/04/2014 04:51PM Last Post by Sublime
	Extruder too tight? by maik	2,122	12	01/30/2014 01:16PM Last Post by AGStumps8807
	Trouble printing motor gear by maik	710	4	01/27/2014 11:16PM Last Post by Robonz
	Calculator size question by flemming	726	2	01/24/2014 07:21PM Last Post by Sublime
	Printing Tantillus extruder by Robonz	663	3	01/23/2014 11:54AM Last Post by Sublime
	Kisslicer by Happycamper	3,432	11	01/22/2014 12:47PM Last Post by Happycamper
	Tantillus heated bed using aluminium clad element by Robonz	1,245	7	01/20/2014 10:12PM Last Post by Robonz
	Print Issues by Happycamper	477	8	01/20/2014 12:08PM Last Post by Happycamper
	Alignment issues by maik	663	6	01/15/2014 04:00AM Last Post by Sublime
	Tantillus Case printed in one shot by beverageexpert	740	4	01/14/2014 02:45PM Last Post by Sublime
	Belt drive extruder by wingnut	1,231	8	01/13/2014 04:42PM Last Post by Sublime
	Alas printing, well sorta by flemming	1,116	16	01/08/2014 12:44AM Last Post by Robonz
	Z wobble hack - printed part by Robonz	2,570	13	01/07/2014 01:54PM Last Post by wingnut
	New build extruder troubles by flemming	660	6	01/04/2014 06:32PM Last Post by flemming
	Making Embossed letters stand out on models by willworkforplastic	963	3	12/28/2013 10:34PM Last Post by willworkforplastic
	Broken extruder by maik	512	6	12/28/2013 07:47PM Last Post by willworkforplastic
	Build plate dimensions by wingnut	776	6	12/24/2013 01:41PM Last Post by Sublime
	Minimum Temp by wingnut	600	8	12/19/2013 03:58PM Last Post by Sublime
	Sparse spots on layers by maik	479	2	12/19/2013 01:45AM Last Post by Sublime
	Tantillus Rods by slashflame	1,009	4	12/18/2013 09:42AM Last Post by Ataraxia
	X AXIS on E1 RAMPS 1.4 sprinter firmware by ale92	669	2	12/17/2013 05:11PM Last Post by davidefa
	Y only moves in 1 direction by Turnrock	726	8	12/17/2013 05:33AM Last Post by ale92

Page 4 of 11 Pages:

1 2 345