Welcome! Log In Create A New Profile

Mendel90

http://reprap.org/wiki/Mendel90

Page 31 of 37 Pages:

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	melzi not reading temp with nophead's firmware by goopyplastic	885	3	08/08/2013 01:19PM Last Post by goopyplastic
	Skeinforge error by danlad1631	975	5	08/08/2013 08:59AM Last Post by DeuxVis
	Mendel90 in Performance Bikes mag by martybee58	805	1	08/07/2013 09:13AM Last Post by martybee58
	PSU showing 13.4v ok to use? by goopyplastic	597	2	08/06/2013 04:22PM Last Post by nophead
	Z motor gets stuck? by bengk	936	4	08/05/2013 05:10PM Last Post by nophead
	skeinforge ABS settings by threedyprinter	911	3	08/04/2013 12:16PM Last Post by threedyprinter
	Extruder heater turns off by Anonymous User	606	1	08/04/2013 09:24AM Last Post by Anonymous User
	What's wrong with this print?? (Pages: 1 2) by danlad1631	2,202	36	08/03/2013 03:18PM Last Post by danlad1631
	X-bar clamps snapping, and X belt tension - A proposed solution. by SanjayM	943	3	08/02/2013 12:23PM Last Post by SanjayM
	questions to mendel90 sturdy by neptunier	797	3	08/02/2013 06:47AM Last Post by nophead
	Custom G-codes by Citrushund	2,072	11	08/01/2013 04:16AM Last Post by QuackingPlums
	Beware Anti Vibration - slic3r by threedyprinter	1,668	6	07/31/2013 07:57PM Last Post by threedyprinter
	again print problems (Pages: 1 2) by neptunier	2,088	39	07/31/2013 07:38PM Last Post by tbowren
	Fans, fans, fans by jfkoehle	1,071	4	07/31/2013 02:28PM Last Post by Alzibiff
	Power Supply Wiring Confirmation by RyanMark	1,038	4	07/31/2013 05:47AM Last Post by nophead
	COM speed - going beyond 250K ? by weirdgod	1,426	23	07/30/2013 08:15PM Last Post by nophead
	Ribbon cable current rating by Zhangx	2,956	11	07/30/2013 06:38PM Last Post by nophead
	What's next? by Anonymous User	658	1	07/28/2013 08:00PM Last Post by Anonymous User
	Y idler without the need to loosen the bolt from underneath by Anonymous User	809	4	07/25/2013 05:10PM Last Post by Anonymous User
	Dual extruders on a larger Mendel90? by CraigRK	3,166	23	07/25/2013 06:02AM Last Post by nophead
	Larger Nozzle Size by RyanMark	568	2	07/25/2013 05:56AM Last Post by nophead
	Filament tube routing by pendragn	1,511	11	07/22/2013 06:36AM Last Post by Amir
	Broken X idler - axis not level by richgain	993	3	07/19/2013 04:17AM Last Post by richgain
	quality issues by klayus	715	3	07/17/2013 11:12AM Last Post by Jonny1983
	thermistor by zug	790	2	07/16/2013 12:38AM Last Post by Anonymous User
	Speeds, Feeds and Flows by Mogal	2,490	18	07/15/2013 12:52PM Last Post by QuackingPlums
	Layers are moving on Y axis by Șap7e	740	4	07/14/2013 08:31PM Last Post by nophead
	broken jhead by klayus	1,061	11	07/13/2013 03:55PM Last Post by nophead
	Extruder Stopped Working? by gaahrdner	959	3	07/10/2013 10:49PM Last Post by gaahrdner
	Print Qualtiy Problems by RyanMark	900	4	07/10/2013 08:45AM Last Post by rhmorrison

Page 31 of 37 Pages: