Welcome! Log In Create A New Profile

Advanced

Mendel90

http://reprap.org/wiki/Mendel90 
Subject Views Posts Last Post

GT2 Belt STL's, need help.

by isolt
1,768 22 06/21/2013 12:15AM
Last Post by isolt

Melzi MCU

by threedyprinter
1,490 7 06/19/2013 04:02PM
Last Post by Anonymous User

Melzi replaced - now the temps are wrong

by zug
1,600 8 06/19/2013 03:39PM
Last Post by Anonymous User

Right Z axis lead screw slipping

by threedyprinter
1,766 9 06/19/2013 07:53AM
Last Post by threedyprinter

Help! Hot end made a 'beehive' around itself! Attachments

by BSBMX
801 3 06/19/2013 07:21AM
Last Post by BSBMX

First layer adhesion

by QuackingPlums
1,105 7 06/17/2013 06:08PM
Last Post by QuackingPlums

Mendel90 Z Axis extension

by Zhangx
868 3 06/17/2013 10:06AM
Last Post by Zhangx

Skeinforge Lift & Fan

by RyanMark
1,202 6 06/16/2013 03:03PM
Last Post by RyanMark

New Mendel90 kit finished Attachments

by ttolhurst
1,237 2 06/13/2013 05:13PM
Last Post by isonoob

Vibration of threaded rods (z-axis)

by Bazooka
3,806 15 06/11/2013 05:53PM
Last Post by SanjayM

Why M6 for leadscrew?

by cts519chris
1,751 4 06/11/2013 05:00PM
Last Post by nophead

Sticky LM8UUs

by threedyprinter
1,100 6 06/11/2013 07:01AM
Last Post by nophead

Skeinforge Settings

by zug
748 3 06/10/2013 06:41PM
Last Post by nophead

Hot End shooting sideways

by Jeromelab
1,523 2 06/10/2013 10:10AM
Last Post by nophead

strange repeating rings on prints Attachments

by qwert75
936 2 06/09/2013 03:54PM
Last Post by richgain

E_STEPS_PER_MM Calculation confused smiley

by Citrushund
1,289 3 06/09/2013 07:22AM
Last Post by Citrushund

my 1st attempt at mendel90

by wannabeaflyer
1,012 2 06/07/2013 09:00PM
Last Post by BillyW

Y Positioning Accuracy

by threedyprinter
1,045 4 06/05/2013 12:15PM
Last Post by threedyprinter

Surface Quality

by threedyprinter
796 3 06/01/2013 07:45AM
Last Post by threedyprinter

How smooth is smooth enough for the carriages?

by jrohl
1,092 4 05/30/2013 11:17PM
Last Post by l8nitesurfer

White ABS Supplier and Settings

by RyanMark
831 1 05/30/2013 04:16PM
Last Post by RyanMark

Z Screw wobble

by zug
789 4 05/30/2013 03:34AM
Last Post by QuackingPlums

Printing in the corner...

by zug
1,235 21 05/29/2013 08:48PM
Last Post by jem-tech

Hot end melted into carrier Attachments

by Daytrip00
1,018 6 05/28/2013 09:19AM
Last Post by Jonny1983

ABS settings

by zug
1,048 9 05/27/2013 04:03AM
Last Post by nophead

All Stepper Motors Jump after Homing

by wozzy
1,290 9 05/24/2013 03:08PM
Last Post by ledvinap

Spool Holder for 1kg Spools

by 3ddude
1,520 10 05/24/2013 08:15AM
Last Post by 3ddude

abs filament issues

by qwert75
664 1 05/23/2013 07:44PM
Last Post by qwert75

Y-Axis Limit Switch Not Hitting

by jeffff
1,115 10 05/22/2013 05:17PM
Last Post by ledvinap

Skeinforge - not extruding?

by weirdgod
1,218 8 05/22/2013 04:15PM
Last Post by weirdgod