Welcome! Log In Create A New Profile

Mendel90

http://reprap.org/wiki/Mendel90

Page 8 of 37 Pages:

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	Extruder starts fine and then is spinning too fast (grinding filament) by Tengushi	1,323	5	06/18/2015 11:03AM Last Post by nophead
	Can't see Melzi W/ ATmega1284p 16mHz in arduino by danlad1631	988	15	06/17/2015 08:44AM Last Post by nophead
	Extruder problems by yiancar	954	20	06/16/2015 05:13PM Last Post by hsbontop
	Print just stops? by danlad1631	657	3	06/16/2015 11:25AM Last Post by danlad1631
	Mendel90 + Pronterface + Slic3r = non centered prints by supitsjoecondol	1,127	3	06/15/2015 01:31PM Last Post by Traveltrousers
	Print problem: inconsistent extrusion by gerv	4,102	9	06/10/2015 02:47PM Last Post by nophead
	X axis assembly leveling by rdomunky	1,032	4	06/10/2015 11:45AM Last Post by rdomunky
	Detailed 3D assembly ? by sharonf88	584	5	06/10/2015 07:21AM Last Post by nophead
	Building my first 3d printer - Mendel90 Z axis assembly by sharonf88	646	3	06/09/2015 05:44PM Last Post by sharonf88
	Heatbed temp after finished print by Red_alert	1,008	12	06/05/2015 01:28AM Last Post by Red_alert
	odd marlin firmware issue by 09zx-6r	1,569	16	06/01/2015 12:33AM Last Post by 09zx-6r
	Consistent blobbiness on first n layers by berk	684	9	05/30/2015 11:33AM Last Post by berk
	Help. Y shift halfway through a print. [SOLVED] by lions3	657	6	05/29/2015 08:37AM Last Post by lions3
	Filament Stuck in the Wades Geared Extruder assembly [solved] by John Palmer	824	3	05/28/2015 03:57AM Last Post by QuackingPlums
	Leveling by yiancar	652	4	05/26/2015 06:33AM Last Post by nophead
	Correct Marlin Software by scubi	882	3	05/18/2015 03:09AM Last Post by neildarlow
	Laywoo-D3 anyone? by bastard	1,327	3	05/11/2015 07:43AM Last Post by bastard
	Alternative Thermistor E3D v6 by scubi	1,167	3	05/08/2015 01:38AM Last Post by scubi
	Filament slipping by danlad1631	1,130	29	05/05/2015 02:15PM Last Post by [email protected]
	Setting hotend or bed temperature causes disconnect by nathanmc	966	3	05/04/2015 10:13PM Last Post by nathanmc
	Concave bed by nathanmc	930	7	05/04/2015 02:46PM Last Post by Garry Bartsch
	Has anyone used this controller by stilgarhammer	798	6	05/01/2015 03:32PM Last Post by stilgarhammer
	Replacement set of parts by aardvarkexpress	819	1	04/29/2015 01:01AM Last Post by aardvarkexpress
	repetier-server reset when the heat bed is turn on by wgaona	766	1	04/29/2015 12:43AM Last Post by wgaona
	Mendel90 extruder wiring connector variant offering...(functional mock-up) by NumberSix	1,399	3	04/28/2015 09:35AM Last Post by cdru
	42? by pgringo	699	8	04/27/2015 09:20AM Last Post by cdru
	Suggestions for changing Bronzefill and Brassfill filament? by neildarlow	1,205	4	04/22/2015 09:18AM Last Post by nophead
	Heat Bed help by scubi	3,450	8	04/21/2015 01:31AM Last Post by scubi
	hotend entrance keeps getting plugged by amell	812	3	04/16/2015 05:28PM Last Post by yak54x
	Print slanting to the left by Chavaquiah	808	3	04/16/2015 06:22AM Last Post by Chavaquiah

Page 8 of 37 Pages: