Welcome! Log In Create A New Profile

Problémy

nefunguje to

Page 1 of 9 Pages: 12 3 4 5

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	[problemy] - kalibrace (Pages: 1 2 3 4) by raptik	5,976	91	12/26/2015 04:55AM Last Post by Bezdak821
	Megatronics 2.0 arduino mega 2560 by paycz	424	3	12/22/2019 05:47AM Last Post by paycz
	Problem s extruderem MK8 na Prusa I3 by sweetboi	910	2	07/27/2019 01:49PM Last Post by ANDY1955
	Nevzhledný povrch tisku by MVano	500	4	07/10/2019 10:09AM Last Post by Prometheuss
	PC/ABS Plasty Mladeč by Prometheuss	645	1	06/11/2019 08:57AM Last Post by Prometheuss
	nežádoucí výplň první vrstvy by milou	613	1	03/26/2019 05:35AM Last Post by milou
	Jak nastavit tiskarnu. by barbucha	573	4	01/09/2019 07:49AM Last Post by barbucha
	Tisk za teplých dní by Prometheuss	642	7	06/28/2018 08:34AM Last Post by Prometheuss
	Jak na slicování světlovodu ? by vaclavpe	916	1	09/24/2017 02:16PM Last Post by vaclavpe
	tiskárna nahřívá jen 5-10 vteřin , pak přestane by milou	861	1	09/21/2017 07:34AM Last Post by milou
	LCD funguje pouze s PC by Krnovacek	605	2	08/31/2017 07:45AM Last Post by dan
	Problém s začátkem tisku by Lugy	725	2	07/14/2017 07:22PM Last Post by Lugy
	Napájení podložky by MIchalBuran	1,107	2	06/23/2017 03:14PM Last Post by MIchalBuran
	REBEL III - v průběhu tisku vynechává osa Z by Tokr	833	1	06/14/2017 09:42AM Last Post by Tokr
	Problém s Hotendem by MIchalBuran	854	1	04/13/2017 08:38AM Last Post by MIchalBuran
	Merlin - upgrade by lahvo	861	1	04/10/2017 08:14AM Last Post by lahvo
	Sekání filamentu by boylucky	1,198	6	04/07/2017 12:16PM Last Post by boylucky
	Hučiace motory by markus993	882	1	03/17/2017 04:10PM Last Post by markus993
	nedokonale vrstvy by paycz	893	3	03/15/2017 06:21AM Last Post by Kopy
	boreni hotendu pri tisku by okoudous	787	4	03/15/2017 06:19AM Last Post by Kopy
	tisk tvarové plochy bez podpory by Kopy	819	4	03/15/2017 06:16AM Last Post by Kopy
	Megatronics v3 (echo:busy: processing) by Nemesis94	903	2	03/10/2017 06:27PM Last Post by Nemesis94
	Invertovnání os po auto levelingu by Ligooo	733	2	02/20/2017 03:54AM Last Post by lahvo
	Správný rozměr dílu by Prometheuss	773	2	02/14/2017 12:34PM Last Post by Prometheuss
	Jak tisknout ozubená kola by Prometheuss	1,410	5	12/20/2016 01:37PM Last Post by Prometheuss
	TR8X8 nastavení by Root1	825	1	12/19/2016 05:19AM Last Post by Root1
	Teplotní čidlo by MIchalBuran	706	3	09/08/2016 02:33PM Last Post by MIchalBuran
	Problém pri tisku PLA a ABS by mraviation	948	1	08/24/2016 04:17PM Last Post by mraviation
	Sekání ABS by jeninicicek	717	6	08/19/2016 01:25PM Last Post by jeninicicek
	změna v repetiéru se neuloží by milou	732	2	08/18/2016 06:57AM Last Post by milou
	Problém s ABS by mraviation	688	4	08/14/2016 09:46AM Last Post by dan

Page 1 of 9 Pages: 12 3 4 5