Welcome! Log In Create A New Profile

Problémy

nefunguje to

Page 4 of 9 Pages:

1 2 345

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	Dual Extruder - chyba při přepnutí by romoli	729	1	08/24/2015 12:53PM Last Post by romoli
	Prosím o radu by ballbutick	663	6	08/24/2015 05:24AM Last Post by ballbutick
	Prvni tisk (Pages: 1 2 3) by volt	5,045	78	08/14/2015 12:19PM Last Post by polikles
	Zapojení motorů by Freezac	634	3	08/08/2015 06:10PM Last Post by Freezac
	Ztráta kroků by Tomascnc	843	6	07/27/2015 02:19PM Last Post by milou
	Nylon by CADS	718	1	07/16/2015 08:46AM Last Post by CADS
	Přerušení tisku by koty0f	976	7	06/25/2015 06:19PM Last Post by koty0f
	Osa Z 4 motory . by milou	730	5	06/22/2015 06:18AM Last Post by raptik
	Software pro support materialu ? by bluewave65	617	3	06/18/2015 04:20PM Last Post by gumitek
	posunuti zakladni pozice by krpy	634	3	06/16/2015 09:08AM Last Post by krpy
	minitronics 1.1 jak nahrat spravnej firmware potrebuji poradit by vladcev	693	3	06/13/2015 04:46PM Last Post by Jenda_T
	Rozdílné teploty u ABS by pfifferling	860	4	06/13/2015 02:41PM Last Post by raptik
	praskání vrstev zvedání rohů extrém . by milou	1,373	13	06/10/2015 01:07PM Last Post by milou
	home nieje na nule by minicico	639	2	06/07/2015 05:04PM Last Post by minicico
	Tisk mostů (bridge) by fugazza	1,080	8	06/06/2015 08:17PM Last Post by nazdarek1980
	repetier - program přestal pracovat,a je potřeba ho zavřít by milou	721	13	05/29/2015 04:20AM Last Post by lubosjerabek
	špatný "Top solid layers"!!! by Kouďák	656	6	05/28/2015 12:36PM Last Post by Kouďák
	pri malych plochach a vysokem tisku se prehriva a bambulati by bluewave65	684	8	05/19/2015 07:33AM Last Post by bluewave65
	Extruder přeskakuje a dochází ke špatné výplni by mitech	1,685	7	05/10/2015 01:14PM Last Post by milou
	změna filamentu ve FW by milou	653	10	05/08/2015 05:45AM Last Post by milou
	Osa Z - vůle v závitech by nomi	791	3	05/06/2015 09:57AM Last Post by nomi
	uhnití 5. vrstev pak srovnání . by milou	624	6	05/05/2015 02:09PM Last Post by milou
	Jak zvetsit detekcni vzdalenost indukcniho snimace ? (Pages: 1 2) by bluewave65	2,025	34	05/03/2015 02:46AM Last Post by bluewave65
	vlnita tlac pri 45stupnoch tlace by risoo	913	5	04/27/2015 04:56AM Last Post by risoo
	Špatný motor? by jeninicicek	649	10	04/22/2015 03:55PM Last Post by Bulman
	nedotahovani kruhu - mezirka by paklic	650	3	04/22/2015 08:36AM Last Post by paklic
	Prvni Vrstvy se neslivaji dobre a male ostruvky jsou prehrate ? by bluewave65	753	4	04/18/2015 11:59AM Last Post by bluewave65
	Tiskárna přestane tisknout by m.d.i.c.	1,163	20	04/09/2015 06:20AM Last Post by CADS
	vlnité rohy by PIMPin	874	8	04/06/2015 04:11AM Last Post by PIMPin
	Netiskne podle G-kodu by zlygriz	761	8	04/05/2015 01:23PM Last Post by zlygriz

Page 4 of 9 Pages:

1 2 345