Welcome! Log In Create A New Profile

Problémy

nefunguje to

Page 6 of 9 Pages:

4 567 8

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	Merlin by CADS	757	2	11/13/2014 08:07AM Last Post by paklic
	Slic3r - výška první vrstvy by FBITuco	1,514	8	11/09/2014 10:05AM Last Post by psticha
	3DRAG nahodilý posun při tisku v ose Y by suri2	1,137	21	11/03/2014 05:28PM Last Post by jimcha
	Hotend by CADS	841	8	10/31/2014 03:46AM Last Post by CADS
	Kdyz kruh neni kruh na tiskarne Delta by charlie2806	763	2	10/30/2014 03:46AM Last Post by charlie2806
	Extruder pouze jedním směrem by charlie2806	807	10	10/28/2014 06:01AM Last Post by charlie2806
	zezačátku tisk super, pak katastrofa by Polar_bear	1,168	8	10/17/2014 03:12AM Last Post by frada
	Nedokonalé výplně by pfifferling	802	1	10/10/2014 10:25AM Last Post by pfifferling
	Zasekavanie extruderu (preskakovanie motora) by Pepcox	1,813	11	10/03/2014 11:30AM Last Post by raptik
	zvedající se rohy by pfifferling	4,835	11	09/29/2014 09:44AM Last Post by pfifferling
	heat bed nehreje by risoo	1,115	5	09/27/2014 01:49PM Last Post by raptik
	Kalibrace (nastavení) osy Z by petrk	3,043	10	09/24/2014 09:19PM Last Post by Korny
	too long extrusion prevented by dj_god	708	3	09/24/2014 01:56PM Last Post by dj_god
	Tolerance by pfifferling	640	4	09/16/2014 07:57AM Last Post by raptik
	zkusenosti s bojem s timhle??? by raptik	1,292	1	09/07/2014 01:27PM Last Post by raptik
	Po zkratu Extruder motor nejede by Codiacx	3,395	4	09/06/2014 10:49AM Last Post by Bajn
	Pištění motorů by gumitek	996	2	09/02/2014 12:25PM Last Post by jokejoke
	Prutok materialu tryskou by Bulka	3,186	28	08/13/2014 12:29AM Last Post by majkl
	Přerušení tisku by CADS	1,661	19	08/07/2014 06:02AM Last Post by FBITuco
	Problém se zvětšováním objemu plastu by Neon3	716	3	08/03/2014 05:24PM Last Post by Neon3
	Nedotahování perimetru by gumitek	785	3	08/03/2014 03:29PM Last Post by dj_god
	Feedrate by ZheFear	1,228	11	07/29/2014 06:30AM Last Post by raptik
	Nestabilní připojení tiskárny by petrk	788	11	07/26/2014 04:07PM Last Post by raptik
	pomoc nastavením (Pages: 1 2) by suri2	3,042	34	07/16/2014 10:15AM Last Post by suri2
	splasena tiskarna by okoudous	772	2	07/14/2014 02:16PM Last Post by raptik
	reprap - kalibrace (Pages: 1 2 3 4) by volt	7,322	96	07/10/2014 09:40AM Last Post by Kopec
	Asi chyba instalace repetiera by milou	924	13	07/07/2014 07:42PM Last Post by majkl
	amps + arduino heat senzor problem by Bajn	702	10	07/07/2014 11:00AM Last Post by majkl
	chovani extruderu by Bajn	1,379	9	06/22/2014 05:00PM Last Post by petrk
	Brown out reset problem by suri2	708	4	06/16/2014 05:20PM Last Post by suri2

Page 6 of 9 Pages:

4 567 8