Welcome! Log In Create A New Profile

Problémy

nefunguje to

Page 7 of 9 Pages:

5 678 9

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	vlastní blbost - únik z extruderu - a co s tím? by suri2	731	4	06/14/2014 09:40AM Last Post by petrk
	Nastavení maximální teploty ve firmwaru by petan86	1,430	16	06/04/2014 07:57AM Last Post by FBITuco
	Problém při dlouhodobém tisku by Studna	1,005	16	05/18/2014 10:18AM Last Post by fugazza
	problem Z-motory by Bajn	621	10	04/29/2014 05:37AM Last Post by Bajn
	[ Problém ] Auto bed level systém by gumitek	798	8	04/28/2014 04:03AM Last Post by dan
	problém se slickerem by Adryane	946	10	04/23/2014 01:43PM Last Post by Adryane
	Rocstock by startQ	821	7	04/23/2014 01:00PM Last Post by Bajn
	Nedotahování vrstev by lubosjerabek	1,263	7	04/23/2014 05:19AM Last Post by lubosjerabek
	nefunkcni heatbed by Bajn	674	4	04/22/2014 12:53AM Last Post by FBITuco
	kvalita tisku by m.d.i.c.	793	1	04/06/2014 11:11AM Last Post by m.d.i.c.
	zamrznutí tisku na čekání na cílovou teplotu by drajos	781	4	04/02/2014 01:48PM Last Post by drajos
	Špatný tisk by georg	1,540	10	03/18/2014 04:08PM Last Post by georg
	PLA a kovovy hotend by dj_god	908	5	03/07/2014 04:47AM Last Post by dj_god
	Ofuk výrobku při tisku by FBITuco	859	2	03/05/2014 12:25AM Last Post by majkl
	Kalibrace - špatná výška vrstvy by FBITuco	1,930	10	02/26/2014 05:21PM Last Post by jokejoke
	Bovden by Lukyn	1,608	3	02/26/2014 02:32PM Last Post by Lukyn
	firmware Sprinter x Marlin by stryc	963	4	02/24/2014 11:23AM Last Post by stryc
	Oprava prasklého dílu z ABS plastu by P3T3	4,735	7	02/22/2014 05:40AM Last Post by Tono
	Model se v polovině tisku odlepí od hotbedu by xhonzax	2,750	12	02/19/2014 06:17PM Last Post by xhonzax
	Nefunguje nic (Pages: 1 2) by Lukashom	1,579	48	02/13/2014 10:56PM Last Post by Kopec
	Barvy - tj více extruderů by dj_god	757	1	02/13/2014 05:29AM Last Post by dj_god
	NEJEDE POMOC by Sandoz	715	1	02/10/2014 11:01AM Last Post by Sandoz
	USB chybové hlášení by Rossky	721	2	02/05/2014 07:47AM Last Post by lubosjerabek
	netopí Hotbet by Rossky	1,016	15	02/02/2014 01:34PM Last Post by camel1cz
	3DRAG teplota Heated Bed by Prometheuss	1,184	26	01/18/2014 05:50AM Last Post by Prometheuss
	Motory na ose Z se točí, jak chtějí (Pages: 1 2) by xhonzax	1,740	35	01/10/2014 01:01AM Last Post by jirpil
	vibrace? i2 by raptik	702	2	01/06/2014 02:15PM Last Post by raptik
	problem - i2, posun Y ? by raptik	1,043	22	12/15/2013 11:13AM Last Post by Anonymous User
	Teplota hotendu pri tisku by volt	1,556	13	12/11/2013 04:43PM Last Post by majkl
	Zrcadlení výtisků by svejk	1,076	13	12/07/2013 09:44AM Last Post by Rossky

Page 7 of 9 Pages:

5 678 9