Welcome! Log In Create A New Profile

Mechanika

mechanické konstrukce, Prusa, Rostock ...

Page 3 of 4 Pages:

1 234

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	trapezovy sroub by petan86	1,930	18	01/16/2014 04:36AM Last Post by camel1cz
	Materiál - překližka vs plast by Vinie	1,641	16	01/11/2014 03:14AM Last Post by P3T3
	hotbed upevneni by Bajn	1,285	7	12/31/2013 08:07AM Last Post by Forrest
	rezani hliniku by Bajn	1,095	6	12/29/2013 05:24AM Last Post by Forrest
	Řetěz na kabely na ose X by buben	1,095	12	12/20/2013 09:06AM Last Post by buben
	Díly Hotendu by Rossky	990	8	12/16/2013 09:42AM Last Post by Rossky
	Šrouby v tisknutých dílech by Axamith	1,044	3	11/02/2013 05:44AM Last Post by Axamith
	Mazání lineárních ložisek by Prometheuss	4,116	12	10/25/2013 01:19PM Last Post by dan
	RepRap Rebel II by janickaaa1919	2,587	26	10/20/2013 05:21PM Last Post by janickaaa1919
	Lineární vedení vs. kladkové vedení by Axamith	2,166	7	10/18/2013 09:39PM Last Post by Axamith
	Nějaké zkušenosti s darwinem?? by malicek3471	1,066	1	10/07/2013 06:19PM Last Post by malicek3471
	Ozubený řemen VS šroub by zakoj	1,044	3	10/03/2013 04:57PM Last Post by dan
	extruder idler srouby by raptik	958	7	10/02/2013 02:36PM Last Post by raptik
	Delta: řemen vs šňůra by Lukyn	950	7	09/26/2013 12:24AM Last Post by Axamith
	linearni vedeni - nahrada za vodici tyce by Bajn	3,637	17	09/19/2013 06:27AM Last Post by Axamith
	Výběr řemenu a řemeniček by xhonzax	1,129	4	09/08/2013 02:40PM Last Post by ku8az
	Rozměry by Naglafar	1,689	13	08/27/2013 05:11AM Last Post by Axamith
	Jakou postavit PRVNI 3D tiskarnu? (Pages: 1 2) by neBulizer	14,567	40	08/26/2013 08:54AM Last Post by dan
	Pár rad pro začátečníka "stavěče" by drom	1,474	13	08/16/2013 01:39PM Last Post by Vinie
	Prusa i2 alebo i3? by WannaBeGnome	1,056	4	08/15/2013 12:56PM Last Post by dan
	Prusa i3 kit by Mikyner	1,365	3	08/11/2013 04:25AM Last Post by drom
	Řemany a řemenice by Bossd	1,001	7	07/10/2013 08:00AM Last Post by jirpil
	Rostock by 999999333	973	3	06/10/2013 05:12PM Last Post by Bajn
	Hlučná ložiska by FeeTee	1,140	11	06/07/2013 02:01AM Last Post by Dupl3xx
	3D tiskarna z cinske elektroniky a hlinikovych profilu - slo by to? by misil	4,876	22	06/04/2013 03:03AM Last Post by dan
	Stavba prusa i3 by Anonymous User	1,772	13	05/29/2013 04:12AM Last Post by Anonymous User
	Začátečník a hromada dotazů by Winc	1,773	16	05/10/2013 01:33PM Last Post by jirpil
	Prusa i3 rám - materiál by jokejoke	1,610	8	02/25/2013 06:11AM Last Post by blazra
	Soubory plastů na Prusa i3 by PazziCZ	1,655	6	02/19/2013 03:22AM Last Post by dysgenio
	Krokový motor s převodovkou 1:50 by Pepe	1,575	3	01/22/2013 11:35AM Last Post by Pepe

Page 3 of 4 Pages:

1 234