Welcome! Log In Create A New Profile

Advanced

Ormerod

RepRapPro's Ormerod http://reprap.org/wiki/Ormerod 
Page 1 of 82    Pages: 12345NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

Removing Crimps from Hotend Connector? Attachments

by auser 		75 7 04/16/2019 03:54AM
Last Post by auser

Bringing my Ormerod v1 back from the dead Attachments   (Pages: 1 2)

by DanV 		980 32 04/15/2019 11:20AM
Last Post by Fatlab

Ormerod 1

by Peter464 		103 6 04/10/2019 05:19PM
Last Post by dc42

Is my psu dying?

by Sardi 		173 17 04/01/2019 11:23AM
Last Post by Sardi

Ormerod FreeCAD Rework & My Ormerod Itteration Attachments

by WesBrooks 		533 24 03/13/2019 05:32PM
Last Post by WesBrooks

5 Years ago - It was the best of times, it was the.. Attachments

by ormerod168 		365 10 02/12/2019 07:54AM
Last Post by Ormerod187

Trying out 1.23 firmware

by PvtTUX 		155 3 02/11/2019 01:30PM
Last Post by PvtTUX

Adding a limit switch to x axis

by Sardi 		148 3 02/09/2019 05:51AM
Last Post by Sardi

Banding on walls? Attachments

by veryevil 		206 9 01/25/2019 05:42AM
Last Post by cheeseandham

Laser head on ormerod

by spiff 		134 5 01/22/2019 04:37AM
Last Post by spiff

Laser cut Aluminium X-Arm & Rib kits....   (Pages: 1 ... 18 19 20)

by Davek0974 		26,968 581 01/20/2019 09:04AM
Last Post by Davek0974

Back again after 3 years

by spiff 		364 22 01/12/2019 02:20PM
Last Post by spiff

Building an Ormerod 2 from scratch

by sinnedwrong 		1,333 30 01/09/2019 04:18AM
Last Post by sinnedwrong

Ormerod 2 web interface buttons lost Attachments

by DaveGray65 		127 3 01/06/2019 05:38AM
Last Post by DaveGray65

Cooling block - where can I get one?

by tim_h 		171 6 01/05/2019 02:30PM
Last Post by ormerod168

Hotend temperature and heating issue

by paflviet 		145 7 01/04/2019 04:00AM
Last Post by paflviet

More mesh levelling issues

by cheeseandham 		364 22 01/01/2019 03:49PM
Last Post by cheeseandham

Print quality and fine-tuning of settings

by Karoo Klong 		304 12 01/01/2019 03:45PM
Last Post by cheeseandham

Printing ABS

by chriscain 		633 8 12/14/2018 04:48AM
Last Post by Karoo Klong

E3D V6 - Should I change the stock print head?

by Karoo Klong 		193 6 12/14/2018 04:29AM
Last Post by Karoo Klong

Source for STL for part 741 Quick-set hot end fan spacer?

by gwild 		500 18 12/12/2018 02:41AM
Last Post by Karoo Klong

Another alternative Hot-end cooling duct. Attachments

by Form232-tek 		3,384 28 12/12/2018 02:36AM
Last Post by Karoo Klong

where can I get the ormerod.ini of DC42 for slic3r?

by sevenljy 		773 12 12/12/2018 02:34AM
Last Post by Karoo Klong

Ormerod 3

by Treito 		962 21 12/07/2018 07:27AM
Last Post by trevmas

Second printer

by jamesf 		620 21 12/07/2018 07:16AM
Last Post by trevmas

Replaced the cooling fan with a noctua one. I'm sane again!

by improprietary 		730 10 12/06/2018 07:07PM
Last Post by Karoo Klong

Bed.g file

by Sardi 		498 13 12/06/2018 04:16PM
Last Post by Karoo Klong

Layer cooling with an Ormerod 2

by cheeseandham 		269 19 12/06/2018 03:43PM
Last Post by Karoo Klong

HELP -----> Need slic3r config - Start/End G-Code

by ormerod2_user 		257 3 12/06/2018 03:11PM
Last Post by Karoo Klong

Printing Files on my RepRap Ormerod 2

by cjdudley 		228 4 12/06/2018 08:14AM
Last Post by Karoo Klong
Page 1 of 82    Pages: 12345NextLast