Welcome! Log In Create A New Profile

Advanced

Ormerod

RepRapPro's Ormerod http://reprap.org/wiki/Ormerod 
Subject Views Posts Last Post

Fix your clips!

by WesBrooks
125 4 12/05/2018 05:00AM
Last Post by Karoo Klong

The Alumarod needs manual mesh bed leveling   (Pages: 1 2)

by Karoo Klong
624 60 12/03/2018 05:02PM
Last Post by Karoo Klong

Ormerod Bigfoot mod! Attachments

by ormerod168
1,851 20 12/03/2018 06:12AM
Last Post by Karoo Klong

Ormerod 2 Y Axis End Plate Snapped!

by veryevil
152 8 11/30/2018 12:45PM
Last Post by veryevil

(Guide) Swapping from bed.g to 4 point mesh with repeat probes.

by WesBrooks
153 5 11/23/2018 10:59AM
Last Post by dc42

Rapidly becoming a home for old Ormerods!

by WesBrooks
250 6 11/23/2018 07:38AM
Last Post by cheeseandham

Wifi/ethernet conflict

by bartdietrich
163 11 11/21/2018 03:48PM
Last Post by cheeseandham

Bringing my Ormerod v1 back from the dead Attachments   (Pages: 1 2)

by DanV
919 31 11/19/2018 03:01AM
Last Post by WesBrooks

Bed leveling issue - how is this even possible?   (Pages: 1 2)

by Sardi
4,339 38 11/15/2018 06:04PM
Last Post by Karoo Klong

Any Ormerod oners from Cape Town?   (Pages: 1 2)

by Karoo Klong
1,073 31 11/15/2018 04:44AM
Last Post by Karoo Klong

Show us your settings!

by WesBrooks
180 6 11/14/2018 12:40PM
Last Post by Jon Steward

My Experimental Ormerod 2 Wiki

by cheeseandham
207 9 11/13/2018 05:47PM
Last Post by Karoo Klong

Finally got round to unpacking my Ormerod 113

by Jon Steward
237 12 11/04/2018 01:16PM
Last Post by WesBrooks

Build log: upgrading Ormerod 2 528.2 to Duet Wifi

by gwild
521 9 10/30/2018 01:57PM
Last Post by dc42

ReprapPro Website

by dannystaple
1,271 23 10/24/2018 05:51AM
Last Post by cheeseandham

Y Axis Idler and Motor Mount

by WesBrooks
396 8 10/24/2018 05:50AM
Last Post by cheeseandham

I'm back after few years. Question for new firmware and problems

by antlvk
1,175 9 10/04/2018 09:17AM
Last Post by cheeseandham

ormerod 2 smooth rods loose

by helix.hex
224 2 10/02/2018 04:22PM
Last Post by cheeseandham

Pentarod 5 Axis 3D Printer

by Karoo Klong
1,683 5 09/19/2018 02:06AM
Last Post by Toysrfun

Duet 0.6 can't print gcode files

by BASPRO
182 3 09/06/2018 10:15AM
Last Post by cheeseandham

Reset duet now can’t find correct firmware

by Jamie2065
174 2 09/02/2018 11:33AM
Last Post by ayudtee

6 way hot end connector - what is it?

by WesBrooks
471 7 08/08/2018 09:08AM
Last Post by dc42

Quickset Nozzle?

by WesBrooks
375 3 08/07/2018 08:18AM
Last Post by Karoo Klong

Adrian Bowyer's response to RepRapPro-UK closing down

by reprapprochina
975 2 08/07/2018 06:52AM
Last Post by Karoo Klong

List of crimps used in Ormerod

by droftarts
2,981 16 08/04/2018 09:42AM
Last Post by Karoo Klong

Filement sensor possible?

by Fpex
823 21 07/25/2018 06:51PM
Last Post by dc42

Ormerod V1 rebuild

by madmob
334 12 07/25/2018 01:56PM
Last Post by Karoo Klong

Ormerod2 Lost Contact with Webinterface

by rjmusto
266 6 07/17/2018 06:15PM
Last Post by cheeseandham

Extrusion Profile Used by RepRapPro?

by WesBrooks
215 3 06/13/2018 03:18AM
Last Post by WesBrooks

Bossac commands for Linux

by rjmusto
299 3 06/12/2018 02:57PM
Last Post by rjmusto