Welcome! Log In Create A New Profile

Ormerod

RepRapPro's Ormerod http://reprap.org/wiki/Ormerod

Page 80 of 83 Pages:

78 798081 82

Forum List New Topic RSS

	Views	Posts	Last Post
X-carriage slides off bearing by dsred294	1,256	16	01/05/2014 12:45PM Last Post by virgodave61
Issues found building printer... by TMD_RS436	827	23	01/05/2014 12:20PM Last Post by dc42
Heater switching transients by Radian	2,431	9	01/05/2014 11:48AM Last Post by dc42
Power supply regulation by Rory166	2,851	14	01/05/2014 08:45AM Last Post by bobc
Improving the proximity sensor - SUCCESS! by dc42	3,723	29	01/05/2014 07:41AM Last Post by Radian
Hotend sag solution by dmould	918	4	01/04/2014 03:48PM Last Post by chriscain
Duet 3.3V supply quality (Pages: 1 2 3 4) by Radian	6,952	94	01/04/2014 01:30PM Last Post by Radian
Power supply problems solved by DennisCowdery	1,309	17	01/04/2014 01:11PM Last Post by Radian
Print attempts either choke or ignored.... by gregstah	896	8	01/04/2014 10:44AM Last Post by droftarts
Round rod specification by Rory166	686	6	01/04/2014 09:13AM Last Post by droftarts
Z axis still missing steps, or another problem? by dc42	2,890	11	01/04/2014 08:45AM Last Post by droftarts
Refund time I think.... by gregstah	920	11	01/04/2014 08:28AM Last Post by Treth
Bearings making an awful noise by hughesie	666	5	01/04/2014 03:41AM Last Post by dc42
X-Axis Squealing! by Coolartist87	527	3	01/03/2014 06:03PM Last Post by Coolartist87
Bed Temperature setting? by Jon Steward	579	3	01/03/2014 05:53PM Last Post by Ormerod276
Proximity sensor by Dan77	1,189	17	01/03/2014 05:36PM Last Post by Dan77
Thought I'd share my latest print... by tim_h	749	7	01/03/2014 12:05PM Last Post by iamburny
Z axis problem by gampie	1,241	7	01/03/2014 11:37AM Last Post by dc42
Y Axis - SOLVED by Astute	584	4	01/03/2014 11:36AM Last Post by Astute
Hello by Mikeemoto	703	7	01/03/2014 06:28AM Last Post by Mikeemoto
Pronterface issues by markbee	3,663	19	01/03/2014 05:21AM Last Post by Jon Steward
Power supply cutting out. by tim_h	1,831	13	01/03/2014 02:10AM Last Post by Rory166
Replicating Ormerod by Rory166	895	7	01/02/2014 06:29PM Last Post by Rory166
hot end stays cold by new-3d	625	2	01/02/2014 01:50PM Last Post by dc42
Support Material by hughesie	576	3	01/02/2014 06:56AM Last Post by reprappro
How to remove a print? by Jon Steward	568	4	01/02/2014 04:59AM Last Post by 3D-ES
Alternative ATX power supply options by Treth	652	2	01/01/2014 04:57PM Last Post by Rory166
Y-axis endstop black wiring connectors by JamesR10	752	12	01/01/2014 03:15PM Last Post by Rory166
Which CAD package? by dc42	598	5	01/01/2014 02:24PM Last Post by iamburny
Cheap ebay filament by iamburny	1,405	13	01/01/2014 01:40PM Last Post by Rory166

Page 80 of 83 Pages:

78 798081 82

Ormerod

Duet 3.3V supply quality (Pages: 1 2 3 4)