Welcome! Log In Create A New Profile



http://reprap.org/wiki/Smartrap_mini A new printer near first release, still in development ... Its main goals are ease/speed of assembly, low cost and modularity (being an easy basement for new designs). 
Subject Views Posts Last Post

Begginer question! Bed tilt problems!

by Rush
330 2 04/07/2016 11:47AM
Last Post by atheimer

Gt2 Idler Attachments

by CeledaBcn
349 1 04/03/2016 05:53AM
Last Post by CeledaBcn

Death of my old Smartrap, and rebirth as a MC2 Attachments

by madmike8
901 6 03/29/2016 11:21PM
Last Post by [email protected]

SmartRapCore print quality/speed?

by spiffcow
557 2 03/06/2016 01:42PM
Last Post by DjDemonD

Upgrade smartrapcore alu to 30 x 20cm bed?

by DjDemonD
391 2 03/02/2016 12:16PM
Last Post by DjDemonD

Z Homing Movement very jerky

by ixlix
460 10 02/20/2016 04:09PM
Last Post by DjDemonD


by fabrice974
364 2 02/18/2016 04:30AM
Last Post by realthor


by DjDemonD
282 2 02/14/2016 10:19AM
Last Post by atheimer

ramps fails to heat hotend higher than 140 celcius

by doede3d
321 3 02/14/2016 09:28AM
Last Post by doede3d

smartcore slicing issue

by Yoko
295 2 02/10/2016 01:30PM
Last Post by DjDemonD

Anyone still use the original smartrap?

by duranza
547 14 02/09/2016 04:47PM
Last Post by duranza

Smartcore build log and pre-build questions   (Pages: 1 2)

by smerrett79
3,802 51 02/06/2016 03:27AM
Last Post by smerrett79

mandrav's SmartCore build Attachments   (Pages: 1 2)

by mandrav
3,302 38 02/05/2016 01:53PM
Last Post by CeledaBcn

Yoko's smart core alu build Attachments

by Yoko
919 9 02/05/2016 09:48AM
Last Post by Yoko

Motor Y and Z autolevel probe issues...

by blindsnake
277 4 02/04/2016 01:51AM
Last Post by s0me

Looking to build... where to start?

by widespreaddeadhead
374 4 02/01/2016 01:14PM
Last Post by Billhc83

Clicking Extruder on Lower Temps Attachments

by Afrei
338 3 01/29/2016 05:09AM
Last Post by Billhc83

OnShape SmartrapCore...

by CeledaBcn
733 4 01/24/2016 05:57AM
Last Post by CeledaBcn

Z axis wobbing large

by solarprism
659 10 01/22/2016 06:12AM
Last Post by Plasticut

Frame corners and not answering emails...

by DjDemonD
326 5 01/22/2016 04:11AM
Last Post by smartfriendz

Smartrap Move and Homing problem.

by lynafox
280 6 01/20/2016 05:10AM
Last Post by lynafox

Considering smartrapcore alu as my first corexy - opinions?

by DjDemonD
1,267 6 01/19/2016 11:24AM
Last Post by atheimer

Banding.... Attachments

by Billhc83
505 5 01/18/2016 09:22AM
Last Post by Billhc83

What parts would I have to change to make a 1m x 1m build Smartrapcore Alu?

by John Cummings
313 2 01/11/2016 03:28PM
Last Post by DjDemonD

Hi all

by _SYCO_
335 1 01/11/2016 08:01AM
Last Post by _SYCO_

Making a 3d printed frame for the Smartrapcore Alu

by John Cummings
427 1 01/02/2016 07:38AM
Last Post by John Cummings

Is it normal not to get answer from smartfriends?

by Yoko
483 9 12/24/2015 10:02AM
Last Post by Yoko

x=0 and stops?

by Wibbles
269 2 12/20/2015 11:26AM
Last Post by Wibbles

Madmike8's Funbot build #2 Attachments   (Pages: 1 2 3 4)

by madmike8
4,049 91 12/15/2015 11:20PM
Last Post by madmike8

Using lead screws for the Z axis on the Smartrap Alu

by John Cummings
625 5 12/11/2015 05:09PM
Last Post by John Cummings