Welcome! Log In Create A New Profile

Smart_Rap

http://reprap.org/wiki/Smartrap_mini A new printer near first release, still in development ... Its main goals are ease/speed of assembly, low cost and modularity (being an easy basement for new designs).

Page 9 of 11 Pages:

7 8910 11

Forum List New Topic RSS

	Views	Posts	Last Post
I have to admit defeat by mondo50m	2,196	5	10/10/2014 10:12AM Last Post by mrmillsy
Preparing to Build... Some Questions by cosmicr	771	5	10/07/2014 12:27AM Last Post by regpye
Regpye's is not an extruder... by cristian	988	7	10/06/2014 10:10AM Last Post by smartfriendz
Verteez Smartrap build (Pages: 1 ... 4 5 6) by verteez	7,479	158	10/06/2014 09:18AM Last Post by verteez
Not possible to home Z due to the lenght of Stepper Motors? by Xhnnas	1,189	15	09/15/2014 08:38AM Last Post by smartfriendz
Hi! I will make smartrap, i'm from spain by danireprap	565	2	09/11/2014 02:53AM Last Post by ldanut
Heat-shrink tubing close to the hotend? by cristian	2,637	6	09/06/2014 11:39AM Last Post by Anonymous User
[Help] smart rap version by jjuasjjuas2	698	2	09/05/2014 04:03PM Last Post by ldanut
Info on the SmartRep Mini ---First post--- by Basher	983	18	09/02/2014 10:22PM Last Post by Anonymous User
Shopping Cart Fixed by regpye	636	1	09/02/2014 05:42AM Last Post by regpye
Printed bushings by mousedigits	648	3	09/01/2014 12:12PM Last Post by mousedigits
Servo Motor Help by BradStaff	9,122	23	08/31/2014 01:42AM Last Post by regpye
my rap by woo	934	24	08/28/2014 08:57PM Last Post by regpye
Smartrap evolution, improvements... (Pages: 1 2 3 4 5) by smartfriendz	7,743	131	08/26/2014 02:17PM Last Post by mikefiatx19
Where did everybody go? by BackEMF	1,143	20	08/24/2014 03:01PM Last Post by regpye
Show your smartrap's print quality by knife-edge	1,094	5	08/22/2014 11:16AM Last Post by CellJeffe
ATX PSU by BackEMF	975	30	08/19/2014 08:13PM Last Post by BackEMF
Reg Pye's SmartRap build (Pages: 1 2) by regpye	4,444	48	08/14/2014 06:52AM Last Post by BackEMF
Smartrap Parts question by knife-edge	781	6	08/11/2014 04:16AM Last Post by benjaminbellamy
Do any one running Repetier firmware? by maxoutny	658	1	08/09/2014 08:22PM Last Post by maxoutny
Which hotend for a smartrap? by cristian	1,458	27	08/04/2014 12:16PM Last Post by BackEMF
Heated bed? by milt	1,158	11	08/04/2014 04:46AM Last Post by ldanut
servo movement by mashedtaters	714	6	07/31/2014 01:19PM Last Post by madmike8
Stabilizing X Axis on 0.4.7 and Earlier Designs by x86Daddy	695	4	07/30/2014 05:18AM Last Post by regpye
How do i test this by BackEMF	720	10	07/30/2014 04:55AM Last Post by BackEMF
Verteez BIG apology. by verteez	573	3	07/27/2014 08:06PM Last Post by regpye
BackEMF's SmartRap 0.4.7 build (Pages: 1 2 3 4 5) by BackEMF	5,606	134	07/26/2014 10:38PM Last Post by regpye
Anyone know what happened to verteez by regpye	564	2	07/26/2014 05:06PM Last Post by BackEMF
Z Offset confused by gimli1003	1,104	3	07/25/2014 11:56PM Last Post by BackEMF
Noise reduction by BackEMF	2,431	15	07/21/2014 08:36PM Last Post by BackEMF

Page 9 of 11 Pages:

7 8910 11

Smart_Rap

Verteez Smartrap build (Pages: 1 ... 4 5 6)

Smartrap evolution, improvements... (Pages: 1 2 3 4 5)

Reg Pye's SmartRap build (Pages: 1 2)

BackEMF's SmartRap 0.4.7 build (Pages: 1 2 3 4 5)