Welcome! Log In Create A New Profile

Advanced

Problemi e qualità di stampa

Avete appena stampato un cubo ed è venuto fuori un prisma? Volete un parere sulla qualità della stampa? Chiedete consiglio qui.
Se siete agli inizi non chiedete qui ma nella sezione dedicata ai principianti. 
Subject Views Posts Last Post

Problema asse z

by Napolitanodiberlino
409 17 06/18/2014 02:02PM
Last Post by Napolitanodiberlino

angoli non perfettamente lineari Attachments

by amario57
421 8 06/18/2014 11:51AM
Last Post by amario57

stampa particolare Attachments

by amario57
412 13 06/17/2014 03:02PM
Last Post by amario57

Problema stampa imprecisa

by antony95
536 2 06/17/2014 05:22AM
Last Post by Nicola P

Prima prova Attachments

by Tester
911 24 06/16/2014 04:37PM
Last Post by Tester

L'hotend si blocca

by rdware
1,863 22 06/16/2014 11:07AM
Last Post by bertnick

Problema di stampa Attachments

by Lemonz
765 23 06/15/2014 03:19PM
Last Post by Lemonz

Problema asse Y minitronics

by Darckan85
329 2 06/15/2014 04:51AM
Last Post by Nicola P

asse z non funzionante   (Pages: 1 2)

by marcogeraldi
1,322 34 06/14/2014 01:00PM
Last Post by marcogeraldi

Problema fin dalla nascita di questa stampante Attachments

by vitelli
827 22 06/13/2014 05:17PM
Last Post by Danio Bonello

Problema : Non estrudo abbastanza

by Shraulinger
399 8 06/12/2014 02:23PM
Last Post by immaginaecrea

Rostock, aumentare la qualità Attachments

by Day_sleeper
366 1 06/11/2014 09:40AM
Last Post by Day_sleeper

stampa..."screpolata"

by revega
448 4 06/11/2014 03:08AM
Last Post by bertnick

prusa i3 non funzionante

by marco97
666 6 06/09/2014 11:01PM
Last Post by NormandC

brim basso, primo layer alto

by mrlove
488 5 06/09/2014 05:13PM
Last Post by mrlove

ABS fa perdere passi dell'estrusore

by zasf
679 7 06/09/2014 04:30PM
Last Post by zasf

Raccordo idraulico, riuscite a stamparlo? Attachments

by zasf
465 3 06/09/2014 03:35PM
Last Post by zasf

stampa inclinata

by ugo3d
605 20 06/09/2014 06:29AM
Last Post by ugo3d

Zoffset in cura

by mrlove
401 3 06/07/2014 07:22PM
Last Post by mrlove

Abs molle

by Galeots
327 5 06/07/2014 12:32PM
Last Post by gusto

Hot end otturato + Collegamento Termistore Attachments

by Ch4OSm4n
748 13 06/07/2014 08:13AM
Last Post by bertnick

suggerimenti per migliorare (e crescere grinning smiley) Attachments

by lexon
697 12 06/04/2014 12:37PM
Last Post by lexon

ondulazioni laterali in stampa Attachments

by amario57
553 10 06/04/2014 12:06PM
Last Post by gusto

Due domandine al volo

by mrlove
348 4 06/01/2014 07:22PM
Last Post by gusto

Motori kit reprap

by barsigor
566 6 06/01/2014 07:18PM
Last Post by gusto

estrudi o non estrudi?

by mrlove
450 10 05/29/2014 05:39PM
Last Post by mrlove

Risoluzione stampa + Problema estrusore? Attachments

by Ch4OSm4n
1,119 13 05/28/2014 01:58PM
Last Post by lion_heart78

La stampa si inchioda

by zay84
461 3 05/27/2014 12:11PM
Last Post by mrlove

prima stampa e direi che non è proprio venuta bene... Attachments   (Pages: 1 2)

by gundam_gdm
1,089 43 05/26/2014 09:56AM
Last Post by Nicola P

Hotend si raffredda

by V_ger
506 8 05/25/2014 03:32AM
Last Post by maralb