Welcome! Log In Create A New Profile

Stampa 3D per principianti

Non sapete da dove cominciare? Avete letto le FAQ, le guide e volete partire con la costruzione di una stampante ma volete qualche consiglio?
Questa sezione è indicata per chi ha appena iniziato o per chi vuole iniziare a stampare 3D.

Page 4 of 36 Pages:

1 2 345

Forum List New Topic RSS

	Views	Posts	Last Post
Problema con un componente Tronxy x5s by Thomas72	524	3	01/13/2019 07:35AM Last Post by Thomas72
Temperatura soto soglia by turi48	421	5	01/11/2019 11:05AM Last Post by turi48
Rifinitura pezzo stampato by agospaolo89	658	8	12/31/2018 09:59AM Last Post by Luca_Benedetto
info Ruramps4d by Stefano_chi	977	22	12/19/2018 05:30AM Last Post by silvanopas
parametri Velocita infill con simplify 3d by Dado74	1,374	10	11/29/2018 05:44AM Last Post by onekk
problemi con lo script conclusivo by Dado74	496	5	11/27/2018 02:09PM Last Post by Dado74
Geeetech A10m - Area di stampa decentrata by Blacksoldier10	488	2	11/26/2018 03:43AM Last Post by bilanciamist
quale stampante scegliere?? by vic20	1,240	8	11/20/2018 05:06AM Last Post by Lolrubber
3D delta homing issue by Martinpoles	443	6	11/09/2018 09:11AM Last Post by bilanciamist
calibrazione marlin (Pages: 1 2) by gio98	1,475	31	11/04/2018 09:39AM Last Post by onekk
Autocostruzione stampante 3d ( prusa i3 cartesiana) by Revolver	1,283	17	10/23/2018 12:06PM Last Post by onekk
Creatly 3D Ender 3 by Ricky1966	691	3	10/17/2018 03:35PM Last Post by claustro
Stampa con doppio estrusore by Pietrogramma	1,113	5	10/17/2018 09:02AM Last Post by Pietrogramma
problema connessione scheda mks gen 1.4 al pc by gio98	704	5	10/16/2018 02:05PM Last Post by gio98
Stampante 3DRag - Estrusore si abbassa troppo by tom135	594	5	09/30/2018 04:49AM Last Post by tom135
Stampante 3DRag - Problemi Asse Z con Cura Engine by tom135	777	2	09/26/2018 05:28AM Last Post by Aldebaran94
Piano riscaldato alluminio.....domande banali by tronicman	616	6	09/21/2018 11:09AM Last Post by onekk
Affogare dado tra slices by Ricky1966	520	5	09/19/2018 02:23PM Last Post by Ricky1966
Anet A6 vs A8 by Ricky1966	1,057	10	09/10/2018 01:51PM Last Post by Ricky1966
Asse Y non funzionante by Gianmarco	402	2	08/16/2018 08:02PM Last Post by callievi
Misure effector by Renthar	427	1	08/12/2018 05:56PM Last Post by Renthar
Zonestar....quale delle 2? by zonalimitatore	483	9	08/03/2018 04:40AM Last Post by zonalimitatore
Aiuto Tecnico per Configurazione del Marlin sulla Tronxy x5s by enzostelvio	768	1	07/30/2018 05:15AM Last Post by enzostelvio
Kossel Mini by theziojoe	983	14	07/21/2018 04:42AM Last Post by MagoKimbra
Problema zonestar P802QR2 by Marcoinn	477	2	07/18/2018 09:46AM Last Post by Marcoinn
Prusa r2 evo restauro by baronrojosur	803	10	07/10/2018 12:09PM Last Post by Gordie
Prima stampa 3d by carcio	604	4	07/06/2018 09:03AM Last Post by Speriamo_che_funzioni
Problema di slittamento layer.. by Andyrok	482	5	06/28/2018 11:12AM Last Post by Andyrok
Delta - Calibrazione dimensioni by Frankq	593	5	06/27/2018 06:42PM Last Post by MagoKimbra
Modifica Parametri con Configuratore MK by 3dorange	486	6	06/24/2018 03:28PM Last Post by 3dorange

Page 4 of 36 Pages:

1 2 345

Stampa 3D per principianti

calibrazione marlin (Pages: 1 2)