Welcome! Log In Create A New Profile

Advanced

Stampa 3D per principianti

Non sapete da dove cominciare? Avete letto le FAQ, le guide e volete partire con la costruzione di una stampante ma volete qualche consiglio?
Questa sezione è indicata per chi ha appena iniziato o per chi vuole iniziare a stampare 3D. 
Subject Views Posts Last Post

Download Firmware Marlinkimbra Attachments   (Pages: 1 2)

by gpau
2,034 34 12/05/2017 07:26PM
Last Post by MagoKimbra

Mostlycnc e MKduo

by Frankq
521 2 11/25/2017 05:06AM
Last Post by Frankq

PROBLEMA RISCALDAMENTO PIATTO DI STAMPA ANET A8

by frijia_gb
704 3 11/24/2017 05:00AM
Last Post by frijia_gb

High temperature tube

by barsigor
275 3 11/22/2017 01:06PM
Last Post by barsigor

Giunti barre M5

by barsigor
316 1 11/21/2017 03:25AM
Last Post by barsigor

Problema gcode per cambio estrusore cyclops

by rainito
913 24 11/20/2017 04:26PM
Last Post by rainito

Il mio Blog sulla Stampa 3D

by RikyRap
435 1 11/16/2017 12:46PM
Last Post by RikyRap

Stampa con TPU

by Mauri78
698 3 11/14/2017 02:14AM
Last Post by Mauri78

Prima stampante - dubbi

by barsigor
388 2 11/08/2017 09:49AM
Last Post by bilanciamist

Geeetech I3 Alluminum problema Asse z

by rOBYlGS
427 4 11/08/2017 08:34AM
Last Post by rOBYlGS

Calibrazione... dove sbaglio...

by gabrygtt
641 10 11/04/2017 09:54AM
Last Post by gabrygtt

FLUX Delta+

by ugomango
340 3 11/03/2017 12:51PM
Last Post by ugomango

Motore estrusore non va Prusa i3 Pro a Attachments

by lanjazz
427 3 11/02/2017 10:05AM
Last Post by lanjazz

Anet a8 asse z con problemi

by paolinux
1,221 4 11/01/2017 07:13AM
Last Post by paolinux

Problema fine end stop Geetech Prusa i3 C

by gpau
372 7 10/29/2017 03:21PM
Last Post by lukezab

consiglio per affiancamento hobby - modellismo 28mm

by Sanjuras
386 4 10/29/2017 02:29AM
Last Post by Sanjuras

consiglio su stampante

by varehol
371 1 10/24/2017 07:01AM
Last Post by varehol

creality cr10

by blanka
486 2 10/19/2017 09:46AM
Last Post by ManuHC

delta Rostock movimento

by mga
309 4 10/17/2017 05:47AM
Last Post by mga

ramps e ventola raffreddamento PLA Attachments

by Stefano_chi
369 5 10/13/2017 08:23AM
Last Post by king2701

tolleranze parti meccaniche

by enrico pallazzo
354 2 10/01/2017 10:40AM
Last Post by alil2096

Asse x non và in home come dovrebbe

by nanigago
304 3 09/30/2017 10:17AM
Last Post by nanigago

Seconda stampante: consigli nella scelta

by rdware
381 2 09/28/2017 09:23AM
Last Post by alil2096

Settaggio e tolleranze

by Marco-67
344 1 09/26/2017 05:18AM
Last Post by Marco-67

chiarimento su funzione FADE_HEIGHT Attachments

by andrea2
308 1 09/24/2017 07:59AM
Last Post by andrea2

hotbed in vetro consigli/info per montaggio su wanhao i3

by mr.blonde75
376 6 09/23/2017 12:32PM
Last Post by mr.blonde75

Livellamento e sensore auto livellamento

by Marco-67
1,045 7 09/23/2017 07:26AM
Last Post by Marco-67

Asse x va sempre e solo da una parte

by nanigago
484 17 09/23/2017 04:51AM
Last Post by nanigago

Problema Kossel XL Attachments

by gabrygtt
328 4 09/22/2017 12:20PM
Last Post by gabrygtt

spostamento nozzle fuori dal piatto

by Stefano_chi
314 13 09/20/2017 08:57AM
Last Post by Stefano_chi