Welcome! Log In Create A New Profile

Advanced

Elettronica e meccanica

Discussioni sulle parti elettriche ed elettroniche, motori, endstop, etc. Parliamo di struttura della stampante, pulegge, madreviti, boccole, viti trapezoidali, etc. 
Page 51 of 54    Pages: FirstPrevious4950515253NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

sotto al piano molle o no??? confused smiley

by il boso 		570 6 04/27/2014 03:06PM
Last Post by il boso

Settaggi e calibrazione

by Sammy76 		1,157 9 04/27/2014 02:15PM
Last Post by Sammy76

Ramps 1.4 Collegamenti e Raffronti sul web

by Condor 		1,136 2 04/27/2014 01:03PM
Last Post by MagoKimbra

Scelta barre lineari Attachments

by Gigio2k 		1,817 9 04/26/2014 02:40PM
Last Post by Gigio2k

endstop y al contrario? confused...[RISOLTO]   (Pages: 1 2)

by RomanelliAlessio 		4,101 37 04/26/2014 09:30AM
Last Post by il boso

sensore temperatura Attachments

by massimo 		497 3 04/25/2014 06:29AM
Last Post by massimo

Problema motore estrusore

by Leo75 		789 16 04/23/2014 04:22PM
Last Post by Bicicletta

motore estrusore forze perde passi aiuto!

by fr4nc3sco 		824 4 04/23/2014 02:07AM
Last Post by fr4nc3sco

"trasformare" prusa i2 in prusa i3 Attachments   (Pages: 1 2)

by il boso 		1,492 46 04/22/2014 03:32PM
Last Post by il boso

Stampa da SD   (Pages: 1 2)

by bertnick 		3,016 36 04/22/2014 08:42AM
Last Post by MagoKimbra

End stop a 4 vie e diver a4988 per motori 2.5 A

by Condor 		637 7 04/21/2014 08:21PM
Last Post by Gordie

Motore estrusore

by Beginner 		462 1 04/20/2014 03:37PM
Last Post by Beginner

asse x e y quanto posso spingermi col peso?e che pulegge?

by fr4nc3sco 		650 5 04/20/2014 03:09PM
Last Post by alberto

Che ne pensate di questi Driver e Motori sono compatibili con la ramps 1.4?

by fr4nc3sco 		479 5 04/20/2014 11:27AM
Last Post by fr4nc3sco

problema aggiornamento firmware

by ugo3d 		780 13 04/18/2014 03:09PM
Last Post by ugo3d

Motori e Pololu A4988 Attachments

by Patroclo 		611 7 04/18/2014 07:48AM
Last Post by Ivan Bortolin

Re: Cerco file stl tendi cinghia asse x prusa i3 [Risolto]

by scorpion74 		1,717 13 04/16/2014 05:05PM
Last Post by sipperton

asse z un motore sforza di piu [Risolto]

by massimo 		1,431 19 04/16/2014 03:09AM
Last Post by gabriczl

Motori imbizzarriti, bloccati in partenza, a volte vanno in direzioni contrarie

by gabriczl 		513 1 04/15/2014 01:10PM
Last Post by gabriczl

mi si è bruciato un driver??confused smiley

by il boso 		505 3 04/14/2014 05:22PM
Last Post by il boso

Muovi il motorino e bruci l'Arduino ?hot smiley

by Davide (Aqua Dulza) 		943 13 04/14/2014 11:29AM
Last Post by ufra

Problema Ramps 1.4 relativo ad endstop [Risolto]

by Alby 		1,509 13 04/14/2014 01:46AM
Last Post by fr4nc3sco

problemi ramps 1.4

by Surfacemodeler 		648 7 04/13/2014 01:41PM
Last Post by Nicola P

Fusibile F2 - MFR1100 fuso... Attachments

by Mauro 		1,477 23 04/13/2014 06:15AM
Last Post by immaginaecrea

VREF e asse Z

by Duanaz 		706 6 04/13/2014 03:33AM
Last Post by Surfacemodeler

problemi prusa i3

by Surfacemodeler 		1,145 7 04/11/2014 05:31PM
Last Post by Surfacemodeler

Pulegge e cinghie, un po' di matematica. Datemi pareri sulle velocità, grazie

by Gordie 		2,722 9 04/11/2014 08:51AM
Last Post by bonjolo

qualìè il miglior driver compatibile con la ramps 1.4? va bene anche esterno preferibilmente che tenga parecchi A

by fr4nc3sco 		541 4 04/11/2014 05:31AM
Last Post by Gordie

Pololu con vref molto alte

by Giuliano 		1,183 14 04/10/2014 06:44PM
Last Post by pivan

Motore fuso? [RISOLTO]

by frengho 		417 2 04/10/2014 06:56AM
Last Post by frengho
Page 51 of 54    Pages: FirstPrevious4950515253NextLast