Welcome! Log In Create A New Profile

Estrusori, Hotends, Heated bed, Filamenti, etc.

Sezione dove discutere di materiali di stampa e delle parti calde della nostra stampante 3D. Estrusori, Hotends, Heated bed, trafilatura e materiali (filamenti ABS/PLA/etc)

Page 3 of 24 Pages:

1 234 5

Forum List New Topic RSS

	Views	Posts	Last Post
MK8 e groviglio by mr.krash	644	12	04/27/2018 08:38AM Last Post by immaginaecrea
Problema E3D V6 by Renthar	2,486	24	04/16/2018 03:59PM Last Post by alil2096
Devo rifare l'hotend......domande by tronicman	733	7	04/09/2018 05:07PM Last Post by tronicman
Ventole per raffreddare il PLA by mr.krash	826	8	04/07/2018 07:26PM Last Post by Stepper79
Estrusore si blocca by Apeks	496	1	04/01/2018 07:18AM Last Post by Apeks
Estrusore che si blocca e torna indietro. (Pages: 1 2) by sbricchesbrak	2,167	42	03/30/2018 10:19AM Last Post by sbricchesbrak
Problemi di stampa by Cycco	529	8	03/27/2018 02:39AM Last Post by Stepper79
come ottenere stampe impermeabili? by giuseppecalasso	521	4	03/24/2018 08:04AM Last Post by giuseppecalasso
Stampa male dopo alcuni minuti by Simone95	568	7	03/17/2018 06:27AM Last Post by ZIOLele
Diamond Hot End by Mauri78	717	11	03/13/2018 07:07AM Last Post by Mauri78
Cold Extrusion by mr.krash	488	1	03/12/2018 03:22PM Last Post by mr.krash
Estrusore multicolore , e accumulo filamento per spurgo. by Stepper79	728	7	03/11/2018 08:22PM Last Post by Stepper79
estrusore mk8 in alluminio Anycubic by takeoff_82	860	7	03/11/2018 05:37PM Last Post by mr.krash
Dual Hot-End e Zeta by mr.krash	1,001	23	03/06/2018 08:43AM Last Post by immaginaecrea
Intasamento hotend by Cycco	650	11	03/05/2018 05:17AM Last Post by Cycco
Come montare buildtak flexiplate su classico mk2 + vetro? (Pages: 1 2) by pivan	1,291	32	02/25/2018 04:57PM Last Post by Mr Yod
Marlinkimbra 4.3.5 temp_sensore by gioo79	519	5	02/23/2018 04:11PM Last Post by MagoKimbra
Estrusore per Prusa i3 Rework (Pages: 1 2) by alex27riva	2,346	33	02/20/2018 11:17AM Last Post by alex27riva
Pid tuning by dibia	532	1	02/19/2018 02:26PM Last Post by dibia
Piatto forato Zortrax M200 by rdware	2,969	21	02/16/2018 01:03AM Last Post by lucamax
Cartuccia hotend che non riscalda più. by Idas	471	2	02/14/2018 02:16PM Last Post by gadmichele
J-Head Mk V qualcuno lo usa? by karnhack	657	5	02/08/2018 05:20PM Last Post by pivan
Non trovo una soluzione , Temperatura hot end instabile by claustro	1,084	6	02/01/2018 06:04PM Last Post by claustro
Estrusore Pid tune by Adryzz	539	4	01/29/2018 02:57AM Last Post by Adryzz
Diametro reale filo estruso by VittorioMX	680	17	01/27/2018 09:12AM Last Post by VittorioMX
Strane letture da hotend IeC 4.0 by ZIOLele	553	8	01/22/2018 06:23PM Last Post by immaginaecrea
Foglio PEI questo sconosciuto... by KIKKI76	1,166	7	01/20/2018 06:08AM Last Post by whitedavil
Consiglio Hotend by Giuss	609	6	01/19/2018 11:43AM Last Post by Giuss
Err: MINTEMP by Lucab	727	6	01/09/2018 05:08PM Last Post by Noisemaker
Titan extruder E3D e non by bilanciamist	1,282	14	01/09/2018 03:53PM Last Post by Micron792

Page 3 of 24 Pages:

1 234 5

Estrusori, Hotends, Heated bed, Filamenti, etc.

Estrusore che si blocca e torna indietro. (Pages: 1 2)

Come montare buildtak flexiplate su classico mk2 + vetro? (Pages: 1 2)

Estrusore per Prusa i3 Rework (Pages: 1 2)