Welcome! Log In Create A New Profile

Advanced

Estrusori, Hotends, Heated bed, Filamenti, etc.

Sezione dove discutere di materiali di stampa e delle parti calde della nostra stampante 3D. Estrusori, Hotends, Heated bed, trafilatura e materiali (filamenti ABS/PLA/etc) 
Subject Views Posts Last Post

Bed che non completa il riscaldamento

by mr.krash
565 10 05/04/2017 04:57PM
Last Post by mr.krash

pla bronzo ...quale ?

by Amerigo
619 12 05/04/2017 11:55AM
Last Post by Elstak

Motore estrusore non va con 0.1 mm

by DOM
549 10 05/04/2017 11:40AM
Last Post by MagoKimbra

blocco estrusore mk8 su stampe di lunga durata Attachments

by takeoff_82
791 20 05/03/2017 06:13AM
Last Post by takeoff_82

Stampa PA (poliammide - nylon)

by beppexx80
568 7 04/27/2017 01:59PM
Last Post by Elstak

Stampa ABS su piatto in vetro

by ninjamcrew
2,834 19 04/27/2017 04:02AM
Last Post by korrado

Modifica firmware repetier per relè

by 1Classe
493 4 04/25/2017 02:39AM
Last Post by MagoKimbra

Temperature crescono continuamente

by DOM
574 26 04/19/2017 07:29AM
Last Post by DOM

Heated bed alligator board

by lexering1988
529 16 04/05/2017 12:55PM
Last Post by lexering1988

Retrazione mk8 direct lenta

by loscorpione
484 4 04/03/2017 11:51AM
Last Post by Elstak

levigatura ABS con acetone

by settore7G
624 5 03/23/2017 05:57AM
Last Post by immaginaecrea

Doppio estrusore o singolo con convogliatore di flusso?

by Salvatore94
1,099 22 03/23/2017 05:43AM
Last Post by immaginaecrea

Che hot end scegliere Attachments

by eviljeff
650 7 03/19/2017 12:54PM
Last Post by eviljeff

tube stop dell'hotend

by settore7G
534 11 03/16/2017 10:58AM
Last Post by settore7G

Filamento Spezzato

by narcy
507 4 03/13/2017 03:16PM
Last Post by narcy

temperatura Hotend che sballa

by Micron792
386 8 03/10/2017 05:18PM
Last Post by Micron792

estrusore perde passi a metà stampa

by mirki97
483 5 03/08/2017 04:38PM
Last Post by Elstak

Problema dual extrusion, filamento in pausa carbonizza

by Elstak
280 4 03/07/2017 01:33PM
Last Post by Elstak

Piani in Carbonio

by alil2096
572 7 03/07/2017 12:01PM
Last Post by lexering1988

come si stampa il PVA?

by Unky3d
632 7 03/02/2017 11:44AM
Last Post by Unky3d

Conducibilità elettrica PLA

by gobig82
419 4 03/02/2017 11:13AM
Last Post by Noisemaker

PLA decente

by Salvatore94
1,086 13 02/21/2017 06:47PM
Last Post by FoxMar

Filamenti di colori diversi in piccole quantità: dove comprare?

by Noisemaker
393 3 02/21/2017 03:09PM
Last Post by maralb

filamento gomma plastink

by marco97
451 12 02/21/2017 04:49AM
Last Post by marco97

Perchè molti produttori italiani di filamenti non vendono su Amazon?

by Noisemaker
614 13 02/08/2017 01:56PM
Last Post by Elstak

TRAFILATORE ITALIANO - POSSIBILE START UP   (Pages: 1 ... 8 9 10)

by Dieghito81
16,876 275 02/08/2017 07:26AM
Last Post by diyer

Aggiungere il terzo estrusore

by Vindiesel
502 9 02/07/2017 05:35PM
Last Post by truck64

D-Bot direct o Bowden?

by claustro
358 2 02/07/2017 08:31AM
Last Post by ManuHC

filamento 3ditaly

by giannixful
444 5 02/05/2017 01:42PM
Last Post by alil2096

Sturare ugello 0.4 senza le punte apposite..possibile?

by ManuHC
388 8 02/03/2017 07:19PM
Last Post by ManuHC