Welcome! Log In Create A New Profile

Estrusori, Hotends, Heated bed, Filamenti, etc.

Sezione dove discutere di materiali di stampa e delle parti calde della nostra stampante 3D. Estrusori, Hotends, Heated bed, trafilatura e materiali (filamenti ABS/PLA/etc)

Page 8 of 24 Pages:

6 789 10

Forum List New Topic RSS

	Views	Posts	Last Post
Titan E3D by Labieno	612	10	10/14/2016 08:55AM Last Post by Labieno
E3d v5 clone discontinuo by ManuHC	624	19	10/14/2016 01:28AM Last Post by ManuHC
Piatto di stampa 300x300? by claustro	467	1	10/12/2016 03:28PM Last Post by claustro
E3D V.6 clone by volcane	1,194	26	10/12/2016 02:43PM Last Post by volcane
errore temperatura minima by MarK8	922	4	10/06/2016 06:09AM Last Post by MarK8
info estrusore by sp09	431	5	10/06/2016 04:07AM Last Post by bilanciamist
Relè a cosa serve? by Oraziomax	1,515	28	09/28/2016 12:58PM Last Post by rangerone1
Cercasi commenti su filamenti BQ (comparando con filoalfa e paperdifferent magari) (Pages: 1 2) by Sicon	2,609	43	09/27/2016 04:32PM Last Post by paolopa
Principiante by Kacro	444	3	09/27/2016 03:05AM Last Post by Kacro
Filamento trasparente? by claustro	451	4	09/23/2016 06:14AM Last Post by claustro
Stampa TPE by paolopa	443	2	09/18/2016 04:17AM Last Post by immaginaecrea
Problema filamento che si arriccia su se stesso by paolopa	1,924	4	09/14/2016 03:18AM Last Post by paolopa
termistore ricambi per estrusore E3d V6 by Unky3d	494	3	09/09/2016 03:09PM Last Post by Unky3d
Problema temperatura Hotend by Micron792	579	5	09/08/2016 01:17PM Last Post by Micron792
Estrusore HTA3d opinioni? by mr_giac0	514	6	09/06/2016 08:32AM Last Post by mr_giac0
Problema estrusore by Daniele92	390	5	09/05/2016 05:32AM Last Post by Daniele92
doccia concentrata vs ventilatore _aperto_ by qsecofr	582	14	09/01/2016 02:42AM Last Post by immaginaecrea
Hotend IeC Terminator come montarlo sulla stampante by RobbyI3	619	6	08/30/2016 02:49PM Last Post by RobbyI3
greg's wade passaggio rapido da 3 mm a 1,75 consigli by raghi	457	2	08/29/2016 12:27PM Last Post by immaginaecrea
Consiglio estrusore da abbinare con un Iec by Sicon	516	4	08/27/2016 05:16PM Last Post by immaginaecrea
Materiale flessibile trasparente by alil2096	350	1	08/25/2016 10:26AM Last Post by alil2096
Raffreddamento su estrusori diretti [RISOLTO] by Simone98	538	3	08/22/2016 02:44PM Last Post by Simone98
é possibile? by MarK8	374	3	08/17/2016 02:35PM Last Post by enricodare
Consigli spurgo doppio estrusore by Vindiesel	1,119	19	08/11/2016 10:44AM Last Post by immaginaecrea
Dubbio PETG by Adryzz	792	12	08/11/2016 04:24AM Last Post by Adryzz
estrusore con rapporto 1:3 by volcane	755	6	08/10/2016 11:59AM Last Post by immaginaecrea
Info estrusore liqud 3Dline by Frapi	823	22	08/09/2016 02:38PM Last Post by Frapi
ESTRUSORE si raffredda al momento della stampa by califfo	382	3	08/04/2016 03:14AM Last Post by ManuHC
Estrusori e temperature by mr.krash	355	3	07/29/2016 01:31PM Last Post by bilanciamist
problema con motore ridotto by cicciom	367	5	07/29/2016 10:56AM Last Post by cicciom

Page 8 of 24 Pages:

6 789 10

Estrusori, Hotends, Heated bed, Filamenti, etc.

Cercasi commenti su filamenti BQ (comparando con filoalfa e paperdifferent magari) (Pages: 1 2)