Welcome! Log In Create A New Profile

Advanced

GCODE, Software e Firmware

Il codice è la genesi dei nostri oggetti da stampare. 
Page 47 of 53    Pages: FirstPrevious4546474849NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

non parte la stampa da SD

by zimox 		605 9 12/31/2014 09:00AM
Last Post by MagoKimbra

Attivare TEMP_STAT_LEDS

by myo900 		867 3 12/28/2014 07:44PM
Last Post by myo900

Firmware per Hamlet 3dx100 -- PROBLEMA

by domsoria 		516 1 12/27/2014 05:24PM
Last Post by domsoria

simplify3D

by jecker 		1,988 13 12/26/2014 05:22PM
Last Post by mic

Motori non girano nel senso opposto

by Condor 		416 2 12/24/2014 06:03PM
Last Post by MagoKimbra

Chiarimenti G-code

by calogerom 		436 2 12/24/2014 07:01AM
Last Post by MagoKimbra

cambiare posizioni connettori

by il boso 		610 13 12/22/2014 08:57AM
Last Post by il boso

MatterControl - un nuovo slicer

by Qbert25 		583 9 12/17/2014 06:02PM
Last Post by bilanciamist

Cambiare schermata iniziale repetier 0.91 Attachments

by gi94eppe 		741 5 12/17/2014 04:11AM
Last Post by enricodare

marlin fine filamento e lcd Attachments

by Simone98 		3,485 12 12/16/2014 04:10PM
Last Post by Simone98

Esperto PHP JS

by MagoKimbra 		462 8 12/16/2014 03:31PM
Last Post by MagoKimbra

impossibile stampare da SD Attachments

by Racing_34 		605 4 12/16/2014 12:36PM
Last Post by Racing_34

Cambio pin heater bed

by fuckella 		352 3 12/16/2014 04:45AM
Last Post by fuckella

RapR3D gcode editor

by MagoKimbra 		493 1 12/09/2014 05:07PM
Last Post by MagoKimbra

Problema "credo" settaggio firmware Marlin

by wacottin 		507 1 12/09/2014 06:11AM
Last Post by wacottin

MarlinKimbra Attachments   (Pages: 1 2 3)

by MagoKimbra 		4,865 89 12/08/2014 06:04AM
Last Post by Ivan Bortolin

Tracciamento porta seriale

by calogerom 		448 3 12/03/2014 12:42PM
Last Post by calogerom

Come far suonare il cicalino a fine stampa

by markbina 		727 3 11/23/2014 10:34AM
Last Post by markbina

Punti sospesi e cura engine Attachments

by Pierinof3a 		390 1 11/22/2014 04:43PM
Last Post by Pierinof3a

Astroprint print in cloud

by amario57 		364 1 11/17/2014 03:32PM
Last Post by amario57

Interferenze durante il percorso?!

by Qbert25 		368 4 11/17/2014 07:07AM
Last Post by MagoKimbra

LCD tempo rimanente e percentuale completata Attachments

by blackhawk 		434 1 11/14/2014 10:43AM
Last Post by blackhawk

Datemi una dritta per Cura engine

by Pierinof3a 		1,889 20 11/13/2014 04:51PM
Last Post by Pierinof3a

Differenziare infill

by alfresco 		388 4 11/10/2014 12:26PM
Last Post by alfresco

Caricare firmware

by ghirap 		1,712 17 11/07/2014 01:12PM
Last Post by huliofane

Minimum travel after retraction

by michele1982 		1,237 5 11/07/2014 08:51AM
Last Post by michele1982

"PORTATA" in repetier host

by giggi 		1,187 3 11/06/2014 01:45PM
Last Post by giggi

sprinter firmware for melzi

by evon 		527 7 11/06/2014 10:39AM
Last Post by MagoKimbra

altezza sbagliata....[RISOLTO]

by il boso 		487 8 11/04/2014 04:59AM
Last Post by Ivan Bortolin

M104 indesiderato nel gcode [RISOLTO]

by giggi 		393 5 11/03/2014 06:37AM
Last Post by giggi
Page 47 of 53    Pages: FirstPrevious4546474849NextLast