Welcome! Log In Create A New Profile

Advanced

GCODE, Software e Firmware

Il codice è la genesi dei nostri oggetti da stampare. 
Page 51 of 53    Pages: FirstPrevious4950515253Next
Forum List New Topic RSS
Subject Views Posts Last Post

c'è nessuno generatore di gcode che riesce a fare i perimetri con un altezza di layer e i riempimenti con un altra?

by fr4nc3sco 		425 5 05/20/2014 04:40AM
Last Post by fr4nc3sco

repetier firmware qualcuno lo usa?

by fr4nc3sco 		552 4 05/18/2014 03:35PM
Last Post by fr4nc3sco

Un pc e due stampanti.

by RomanelliAlessio 		461 3 05/08/2014 06:57PM
Last Post by RomanelliAlessio

Verifica formato stl

by monte.m79 		435 4 05/06/2014 03:07PM
Last Post by sipperton

CURA: Vasetto aperto! [RISOLTO]

by RomanelliAlessio 		407 3 05/06/2014 10:20AM
Last Post by RomanelliAlessio

problemi marlin e settaggi [RISOLTO]

by gundam_gdm 		798 14 05/05/2014 04:39PM
Last Post by gundam_gdm

Errore in SLIC3R: "G-CODE GENERATO NON TROVATO" Attachments

by deltaforce 		1,385 7 05/04/2014 07:46AM
Last Post by MagoKimbra

avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check.

by Alessio Narder 		2,712 6 05/03/2014 10:01AM
Last Post by Alex9000

Stampe si interrompono (ERRORE CHECKSUM)[RISOLTO] Attachments

by alberto 		564 3 05/02/2014 07:03AM
Last Post by alberto

Cura e .jpg Attachments

by enricodare 		758 7 05/01/2014 07:13AM
Last Post by pivan

Infill differente stesso valore Attachments

by Nicola P 		1,006 10 04/30/2014 03:22PM
Last Post by MagoKimbra

Repetier-Host - problema primi testangry smiley

by Fedus82 		488 1 04/30/2014 10:51AM
Last Post by Fedus82

come procedere, ad installare una prusa i3 su windows vista

by guido canacci 		441 2 04/30/2014 09:39AM
Last Post by sipperton

Aiuto Settaggio Firmware Marlin Su 3DRag

by massimiliano 		2,064 8 04/30/2014 07:38AM
Last Post by massimiliano

[Risolto] Info su G-CODE Marlin

by Federico22 		1,114 6 04/29/2014 04:59PM
Last Post by Federico22

firmware per nuova stampante

by Z171 		480 3 04/25/2014 05:18PM
Last Post by Z171

Problema con REPETIER HOST

by bertnick 		1,662 7 04/24/2014 02:39AM
Last Post by MagoKimbra

CURA **SPOSTARE IL PUNTO INZIALE XYZ**[RISOLTO]

by Fuma 		513 3 04/22/2014 05:38PM
Last Post by Fuma

errore Extruder switched off. MINTEMP triggered ! come si risolve? [Risolto]

by fr4nc3sco 		1,126 19 04/22/2014 01:29PM
Last Post by fr4nc3sco

3D-stampata-server UDOO Quad -> Debian wheezy armHF

by angelo 		685 8 04/22/2014 10:10AM
Last Post by angelo

Software simulazione g-code

by nuvolini 		2,736 4 04/22/2014 08:49AM
Last Post by enricodare

[RISOLTO] Problema Ramps 1.4 Motherboard 33

by Condor 		435 3 04/20/2014 07:33AM
Last Post by Condor

too long extrusion prevented

by laudix 		452 3 04/19/2014 06:42AM
Last Post by immaginaecrea

Software modellazione

by alil2096 		652 4 04/18/2014 03:31PM
Last Post by bertnick

Movimento asse x y

by Surfacemodeler 		741 7 04/18/2014 12:42PM
Last Post by sipperton

Problemi asse Z autolivellante [Risolto] Attachments

by Alex77 		1,207 5 04/16/2014 12:25PM
Last Post by Gordie

RepetierHost si chiude con click destro - Debian

by Gordie 		452 4 04/12/2014 05:31AM
Last Post by Gordie

Repetier-host, Slic3r , Cura quanta potenza di calcolo serve ?

by fr4nc3sco 		883 5 04/11/2014 04:51AM
Last Post by fr4nc3sco

Slic3R ma quanto ci metti? Attachments

by tanbruk 		520 5 04/10/2014 08:13AM
Last Post by tanbruk

modifica firmware per duet

by zaius 		668 10 04/07/2014 07:01PM
Last Post by T3P3
Page 51 of 53    Pages: FirstPrevious4950515253Next