Welcome! Log In Create A New Profile

Extruder, Hotend en Filament

Probleem met je Jhead? Je Greg's of ruzie met je ABS/PLA? hier vind je de oplossing.

Page 1 of 2 Pages: 12

Forum List New Topic RSS

	Views	Posts	Last Post
Welke naam? by jonnie	615	1	03/30/2017 07:10AM Last Post by jonnie
Flex binden met non-flex by Replace	731	1	01/06/2017 01:56PM Last Post by Replace
Taulman print je op ... ? by Replace	720	1	07/31/2016 03:13PM Last Post by Replace
e3D raakt verstopt. by Replace	717	7	07/31/2016 03:12PM Last Post by Replace
filament datasheets by jonnie	744	6	02/29/2016 04:26PM Last Post by jonnie
dutch filament suppliers by sungod3k	1,310	3	02/15/2016 02:07PM Last Post by garaguido
Hoe werkt deze ? by Replace	812	8	02/10/2016 01:07AM Last Post by Replace
Bowden of Direct? by Replace	949	8	02/09/2016 05:27AM Last Post by Frans@France
Ik wil een nieuw hotend bouwen. by Replace	980	8	02/03/2016 06:23AM Last Post by Replace
HeatBreak by Replace	749	1	01/27/2016 11:06AM Last Post by Replace
vastlopen in heatsink by meeswes	740	4	12/12/2015 05:54AM Last Post by Frans@France
Support filament by 3Design	932	6	11/11/2015 11:56AM Last Post by jonnie
Help!! Een paar vreemde lagen by william-green	977	8	03/07/2015 01:32PM Last Post by william-green
Geeetech (E3D) hotend loopt vast (Pages: 1 2) by reeskees	2,751	43	03/06/2015 05:58PM Last Post by jipjip
Wood filament en E3D V6 vraagje by jipjip	961	1	03/06/2015 02:22PM Last Post by jipjip
J-Head raakt steeds verstopt (Pages: 1 2) by valknut	2,459	45	02/13/2015 03:59AM Last Post by SnelleD
Het doel van JHead koeling by valknut	970	4	01/26/2015 02:26PM Last Post by Ohmarinus
J-head extruder temperatuur is 0 by morubil	900	8	01/25/2015 04:22PM Last Post by morubil
E3D v6 hot end versus Merlin hot end. by KeesL	1,418	14	12/27/2014 05:37PM Last Post by KeesL
Filament van Reprapworld... by Nsverhagen	1,520	4	12/14/2014 05:44PM Last Post by Frans@France
Breken PLA by KeesL	3,074	16	10/30/2014 05:18AM Last Post by 3D-ES
extruder 2 wordt niet aan gestuurd vanuit Repetier by MartijnD	947	3	10/27/2014 02:28PM Last Post by MartijnD
Temperatuur hot end varieert. by KeesL	894	6	10/22/2014 10:17AM Last Post by P4tje
Extruder problemen by MartijnD	2,144	13	09/05/2014 07:04AM Last Post by MartijnD
Altijd al willen weten ..... by Replace	887	4	08/09/2014 05:02AM Last Post by fredman
Klein ongelukje by fredman	1,135	19	07/24/2014 09:42AM Last Post by P4tje
verschil in printkwaliteit by 3Design	916	3	07/12/2014 06:30AM Last Post by 3Design
j head nozzle by 3Design	1,049	13	07/03/2014 10:54AM Last Post by Ohmarinus
IKEA SÖRLI spiegels by jonnie	1,948	3	06/14/2014 05:26AM Last Post by jonnie
filament kopen by Maarten Visser	901	6	06/11/2014 01:53PM Last Post by Ohmarinus

Page 1 of 2 Pages: 12

Extruder, Hotend en Filament

Geeetech (E3D) hotend loopt vast (Pages: 1 2)

J-Head raakt steeds verstopt (Pages: 1 2)