Welcome! Log In Create A New Profile

Advanced

Electronica

Ramps of Rumba, Rambo of Mechatronic? Stel hier je vragen over de diverse RepRap oplossingen voor je printer en voor alle relais, zekeringen en voedingen. 
Subject Views Posts Last Post

Bluetooth en Arduino upload

by dutchengineer
106 1 04/03/2018 10:10AM
Last Post by dutchengineer

Hoi! Zijn hier MKS SBase V1.3 gebruikers die willen helpen?

by HugoW
153 1 11/28/2017 02:00AM
Last Post by HugoW

thermokoppelbord v1.0

by jokke0066
187 3 08/27/2017 02:07PM
Last Post by smokey_rs250

Megatronic V3.1 Fan2 werkend krijgen

by thing78
197 1 05/20/2017 08:28AM
Last Post by thing78

Melzi: Geen spanning op end stops

by aadkoene
115 2 11/14/2016 05:59AM
Last Post by aadkoene

stopt zomaar met printen

by william-green
135 3 10/07/2016 05:47PM
Last Post by william-green

auto bed leveling

by willem1691
185 1 08/28/2016 10:53AM
Last Post by willem1691

grafisch kleuren display ramps

by 19roland70
142 4 07/18/2016 04:27PM
Last Post by 19roland70

Filament out sensor feature ?

by Replace
145 2 06/27/2016 05:12PM
Last Post by gforce1

mks tft28 v1.2 smart touch

by nonaak
457 3 05/11/2016 02:55PM
Last Post by nonaak

Steppermotor/Electra? problemen

by Binho88
171 1 03/27/2016 05:59PM
Last Post by Binho88

Melzi upgrade bord ATMEGA 2560 van Xinray

by garaguido
238 6 03/24/2016 02:06PM
Last Post by garaguido

Melzi 2.0 probleem met Vreg op bord

by garaguido
262 2 02/26/2016 11:19AM
Last Post by garaguido

Full grafics LCD display

by garaguido
214 2 02/26/2016 11:16AM
Last Post by garaguido

welke I/O voor led's [Marlin]

by 19roland70
273 2 02/15/2016 03:39PM
Last Post by gforce1

Vref instellen

by 19roland70
425 8 02/04/2016 05:35PM
Last Post by knaapio

Arduino mega doet gek

by Strobaal
202 3 12/29/2015 12:26PM
Last Post by Whaw

Smart LCD display

by garaguido
281 2 11/30/2015 08:17AM
Last Post by garaguido

Dual extruder met print fan aansluiten ramps 1.4

by 118d
263 1 09/06/2015 06:05PM
Last Post by 118d

kleine crimp connectoren?

by jonnie
226 3 08/10/2015 08:24AM
Last Post by jonnie

Electronica vervangen

by jonnie
297 1 04/25/2015 04:28AM
Last Post by jonnie

keuze printer board

by snowleopard
416 6 04/16/2015 01:24PM
Last Post by jonnie

Extruder primen via LCD ?

by Replace
244 5 04/04/2015 03:32PM
Last Post by Ohmarinus

eind stops   (Pages: 1 2 3)

by [email protected]
1,063 62 03/27/2015 10:18AM
Last Post by Ohmarinus

Megatronics v3.0

by PvdBos
267 2 03/24/2015 03:00PM
Last Post by jonnie

Pololu A4988 of A4983?

by oopss
313 6 03/16/2015 01:37PM
Last Post by Whaw

SilentStepStick stille stepper driver

by Whaw
630 13 03/07/2015 03:52AM
Last Post by Whaw

End stops werken niet. Attachments

by Jochem Elf
733 13 02/18/2015 11:56AM
Last Post by jonnie

Extruder mist steps

by Replace
376 12 02/18/2015 10:35AM
Last Post by [email protected]

Steppermotor 0,9° en 1.8° wat is het verschil?

by SnelleD
361 7 02/14/2015 07:59AM
Last Post by [email protected]