Subject		Views	Posts	Last Post
	Reprap I3 need help setting up by Maddog	1,185	3	02/06/2024 05:29PM Last Post by Dust
	thoughts on design by civil	2,202	3	01/17/2024 03:38PM Last Post by VDX
	CoreXY: Non-matching MGN carriages on either side of Y? by DailyFrankPeter	1,329	2	12/01/2023 04:17PM Last Post by Govahnator
	How to avoid strangled cables in cable chains. by Govahnator	1,001	2	11/30/2023 08:47PM Last Post by Dust
	Extruders motors will not turn by Nigel Kelly	1,328	13	11/01/2023 04:44PM Last Post by Nigel Kelly
	Nema23 --> Makerbase --> setup by Arnix	1,481	4	08/27/2023 12:25PM Last Post by Dust
	Megatronics v3 and RepRapDiscount LCD 12864 by julieng7	4,673	9	08/20/2023 06:30AM Last Post by J.Snijder
	moving axis beyond endstop possition by equipment66	1,395	1	08/03/2023 02:00AM Last Post by equipment66
	Updated to latest firmware cannot heat nozzle by sgtmrcooperusmc	1,821	6	07/28/2023 04:52AM Last Post by sgtmrcooperusmc
	What Filament to use to replace a Bakerlite part by zurferjoe	1,622	1	07/19/2023 12:35PM Last Post by zurferjoe
	Is it okay to not to use smooth rods in 3d printer by erensatik	2,655	6	06/26/2023 05:31PM Last Post by the_digital_dentist
	M155 logging ADC values by wa3scm	2,144	3	05/11/2023 01:40PM Last Post by wa3scm
	delta xy grinding noise on specific coordinates by muhbb	2,184	1	04/30/2023 07:20PM Last Post by muhbb
	Creality Ender5 pro with REPRAPDISCOUNT FULL GRAPHIC SMART CONTROLLER by mehbstnc	3,010	3	04/16/2023 02:48AM Last Post by mehbstnc
	How to set custom home position and drive directions by oBezruki	5,271	10	04/03/2023 03:06AM Last Post by dc42
	Original BCN3D RepRap BOM/STLs by rwilson	3,951	2	03/09/2023 07:44PM Last Post by NewPerfection
	Core ZXZY Build Log by zxzy_eng	4,260	6	01/25/2023 01:32AM Last Post by zxzy_eng
	Marlin on cheap Arduino clone by rwilson	3,029	5	01/16/2023 12:33AM Last Post by VDX
	Marlin 2.1.1 Configuration.hsettings ignored by walts	3,134	4	11/28/2022 09:01PM Last Post by Dust
	Help Driving Stepper with Raw GCode by dlamet	3,162	5	11/08/2022 10:57AM Last Post by dlamet
	Steps per mm not updating with new Marlin Flash by dvanommen	12,285	10	10/29/2022 09:50AM Last Post by Dust
	Stepper does not work with one driver, others do by flomei	3,200	3	10/23/2022 08:37AM Last Post by flomei
	Omni3d Rapcraft 1.4 heatblock tightens right down to heatsink by sundaycrunk	3,754	2	10/03/2022 06:17PM Last Post by rq3
	Job Well Done by Ndv19	3,611	2	09/30/2022 02:57AM Last Post by VDX
	Display on LCD not there by Ndv19	4,058	3	09/29/2022 05:14PM Last Post by Ndv19
	Newbie to DIY reprap with questions by tonynsx	3,860	9	09/26/2022 10:25AM Last Post by tonynsx
	My Core XY Printer that took years of building by Govahnator	5,295	4	09/23/2022 03:14PM Last Post by tonynsx
	Creality 4.2.7 END STOPS PROBLEM by Moudry	4,251	6	09/23/2022 02:10AM Last Post by Moudry
	printer executing each command then stopping by dlc60	3,916	4	09/22/2022 08:14PM Last Post by dlc60
	Help needed in setting up an inductive probe by Kyler	6,549	4	08/16/2022 11:16AM Last Post by BHEEEN