Welcome! Log In Create A New Profile

Advanced

Prusa i3 and variants

http://reprap.org/wiki/Prusa_i3 
Subject Views Posts Last Post

Can I add thermal runaway protection to an Ender 3?

by Aldebaran94
1,911 3 08/05/2018 11:16AM
Last Post by Dust

Upgrading Duplicator i3 from Melzi to MKS Baase 1.4 with Touch Screen

by MrPuffyNZ
281 1 08/03/2018 07:53PM
Last Post by MrPuffyNZ

Marlin firmware with folger2020?

by foul_owl
263 1 08/03/2018 05:43PM
Last Post by foul_owl

New first printer zonestar

by zonalimitatore
278 1 08/02/2018 07:57AM
Last Post by zonalimitatore

Marlin vs Repertier

by erniehatt
972 18 07/31/2018 02:56AM
Last Post by erniehatt

Thermistor question

by thequestor
233 3 07/30/2018 09:53PM
Last Post by thequestor

Extruder stops extruding. Attachments

by dlw
266 2 07/27/2018 12:12AM
Last Post by o_lampe

3d printing problems with filament. Attachments

by dlw
276 6 07/26/2018 01:55PM
Last Post by dlw

I3 adding Filament sensor and heatbead auto level Attachments

by Blisk
334 4 07/23/2018 07:53AM
Last Post by Blisk

Graber I3 Titan Aero Upgrade - Layer problem

by raphaelgatti
385 3 07/22/2018 11:17PM
Last Post by raphaelgatti

Tronxy P208: Those who helped dlw please read.

by dlw
311 13 07/22/2018 10:20PM
Last Post by dlw

End of my rope with the Ender 3

by NickNonsense
1,088 3 07/19/2018 09:53AM
Last Post by MCcarman

Potato chip bed

by serdar415
358 6 07/17/2018 02:04AM
Last Post by erniehatt

Direct mounting E3D V5 hot end onto wade extruder

by robotix83
593 3 07/16/2018 04:49AM
Last Post by serdar415

Upgrading only Prusa i3 to MKS sbase 1.3

by robotix83
491 7 07/16/2018 04:45AM
Last Post by MKSA

First layer issue Attachments

by DaSt
389 5 07/13/2018 06:21PM
Last Post by MMcLure

Extruder temperature problem.

by dlw
430 3 07/05/2018 10:02PM
Last Post by dlw

Upload errors

by dlw
258 3 07/05/2018 08:49AM
Last Post by serdar415

Urgent help needed for printer config

by hgreeves
245 6 07/04/2018 07:48PM
Last Post by Roberts_Clif

Z axis motors jamming

by GingerNinja
243 4 07/04/2018 07:22AM
Last Post by GingerNinja

Marlin firmware and controller board configuration help needed ASAP

by hgreeves
688 8 07/03/2018 02:41AM
Last Post by Dust

touch bed leveller

by erniehatt
405 7 07/02/2018 06:58PM
Last Post by cubeconvict

Dual Extruders?

by dilligaf32
265 2 07/02/2018 06:47PM
Last Post by cubeconvict

Marlin firmware upgrade advice needed

by Thereaper
829 8 07/02/2018 06:00PM
Last Post by Thereaper

Melzi to MKS GEN 1.4 conversion - Temperature and Zaxis issue

by Gaz83
686 3 06/29/2018 03:03AM
Last Post by Gaz83

drv8825 problem

by malio77
243 2 06/28/2018 06:32AM
Last Post by o_lampe

Extruder not running...

by GSD
293 4 06/27/2018 01:49PM
Last Post by GSD

Uneven bed

by serdar415
469 11 06/26/2018 06:13PM
Last Post by erniehatt

Building my first 3D printer - Prusa i3 rework based

by niekz
398 4 06/26/2018 10:46AM
Last Post by SteveRoy

Anet A8 and enclosure

by DaSt
608 3 06/25/2018 11:12AM
Last Post by DaSt